ender 5 s1 firmware 3d models

https://www.printables.com/model/255772-cr-touch-left-side-mount-for-ender-3s1s1-proI redesigned it for my Ender 3 S1 Pro.Reasons for remixThe original had its X-offset being-55.5mm however this didn't allow me enough room for my X-axis to reach for...

Although I've only tested this on the S1 Pro, it should also work on the S1 and the S1 Plus, as I believe they all share the same gantry design. You'll need either 8x 10mmx2mm or 4x 10mmx4mm neodymium magnets for this. As strong as you can get...

Remixed from Alex Watsons mount, his design made contact with the bed on my S1 Plus so I extended it and now it fits perfectly, I'm assuming that the S1 Plus extends further than the standard S1.

The ideal position for me would have been central so as not to take up any more space.I have seen other supports that provide for the top mounting of the Ender S1 3 PRO but none have convinced me. I wanted the stand to be sturdy and rigid to minimize...

A collection of extruder spinners I designed for the Ender 3 S1 Pro sprite extruder. I'm unsure if they will work with other makes/models but they print quick, so give it a go! You will need to buy some 4mm dia x 3mm thick magnets for these spinners...

The MkII version of my Ender 3 S1 Drawer Insert, it incorporates: - Smaller front covers as remixed by mw212 (I can't find this thing) to fix the issue of it binding slightly on closing; - a modified space to fit a different set of nippers (PCAFC...

It all depends on the moment 😄 SD extension bracket and cable cover for Creality Ender 3 S1 pro 3D printer. Allows an SD card extension to be placed on the side of the machine with two slots for storing cards. Also a variant with a slot for the...

I designed a clamp for the base of an Ender 3 S1 and modified https://www.thingiverse.com/thing:5643289 a bit (deleted brush part). I used https://www.thingiverse.com/thing:2920060 chain links. You will need 1x Bed clamp, 1x Frame clamp, 18x...

I made it to replace basic lcd of Ender S1 Plus to waveshare 7" due to installing klipper to this printer. In the back there is holder for RPI. Mounted with screws used with basic mount. In future I will upload another holder for this lcd but mounted...

I wanted a mount that worked with my Ender 3 S1 and couldn't find one for the Wyze cam V2, so I took a mount that I liked, added the Wyze bracket to it and then added a little reinforcement. It works. It's pretty good. If I was better with CAD,...

ok, so as some of you may come to find that the Ender S1 has a garbage cooling design. Working on this remix of the EVA carriage system that uses these tri-horn ducts. cool stuff. you'll need some M3 screws of various sizes. 5015 24V blower...

A collection of extruder spinners I designed for the Ender 3 S1 Pro sprite extruder. I'm unsure if they will work with other makes/models but they print quick, so give it a go! You will need to buy some 4mm dia x 3mm thick magnets for these spinners...

Camera mount for the Ender S1 Pro by Creality. Inspired by camera mount designed by TSDano. Some improvements made for more stable and snugger fit: - Added more strength to the body to minimize vibrations. - Resized and reshaped the body to...

This is a quick little box to hide your Ender 3 S1 controller ribbon after you convert to the Sonic Pad. I designed this to make switching between the Sonic Pad and the default controller quick and easy. It keeps the ribbon hidden without having...

I designed a mounting arm that clips on the end of the Y axis on the Ender 3 S1, to support a raspberry pi camera module. Everything prints as they are and without support. The arm has built-in support that can easily be cut off after printing. To...

I needed a camera mount for my Ender-3 S1 to mount my Logitech C920, so I made this. This is v2 with better support for the camera. No shaking now. It will work with any camera that has a normal camera mount thread. ... I'm including the extra...

*This is a remix of [this design on Printables](https://www.printables.com/model/475690-ender-s1-gantry-light-bar).* --- This is a printable light bar support that screws into the existing hex screws at the back of the gantry, no additional screws...

It secures to the Ender 3 S1 top rail with one M5x12 SHCS and a T-nut. Printed in the orientation shown in the rendering, using PLA with .028 layer height, tree supports, and 20% grid infill, it came out rough on the edges, but at 38 minutes to...

... due to too flexible). But once it's in, it's not going anywhere. Unfortunately the printing time gets longer (around 2 hours) Printed using Ender 3 S1, with around 50% infill just for added strength. ...Lower might be feasible, but not tested.

This is fan duct upgrade for the stock Ender 3 S1/Pro fan or Sprite pro extruder. ChangelogUpdate: Aug 2,2022Updated the file with support for resin.Print with hightemp resistant filamentor print it using resin printer for better air flowAdded Stl...

For the lower mount, I took the base of “Creality Ender-3 S1 Pro Yi Home / Raspberry Pi Cam Mount” from SnakeP (https://www.thingiverse.com/thing:5585683), since it fits good on the front corners of the S1 pro. I completely changed the part where...

Creality Ender 3 S1 Pro filament holder extension adapters. Used for adding an additional roll of filament to the standard S1 Pro filament holder. You need a 20mm wardrobe rail from somewhere like B&Q in the UK, and then cut it down to the width...

Displayhalterung für den Ender 3 S1 zur Befestigung des Display an einer anderen Position. Zwei Teile: 1. Grundplatte für die Aufnahme des Displays 2. Wandbefestigung zum Anschrauben an eine vertikale Wand (rechtsseitig) 3. Wandbefestigung zum...

Ender 3 S1 Filament Sensor Mount, I'm using it in my Lack Enclosure. I wanted to use all parts from the original mount because i don't wanted to buy new screws and brass inserts. This is my first ever created 3D Object, so please be kind :-) Print...

This is a drawer for an Ender 3 s1 that holds a Raspberry Pi 4 B, and still has a small storage bin at the back. The loop inside is to zip-tie the power cable for strain relief. I found the base drawer on another site, but it was for the Pi 3B...

... flat cable. ...Prevents end switch and X-axis motor wires from pulling and damage. On S1 Pro flat cable is a little wider and motor/end switch wires are shorter than on S1! ...That's why almost the same clips for S1 couldn't fit on S1 Pro perfectly.

I was unable to find and Ender 3 S1 Pro Tray Insert anywhere so I decided to take a deep dive and dabble in some Fusion 360 3D modelling learning a lot in the process. This is my first 3D model from scratch, my first design that I'm sharing with...

So I remixed the display camera mount and the Z-Axis Handle to one modell and adjusted the screw hole size.See https://www.printables.com/de/model/172815-ender-3-s1-pi-camera-mount for the holder and screw to mount the case or print the version,...

But there was non for my Ender 3 S1 Pro in thingiverse, so I learn basic Fusion 360, and did my own model!I did like 25 iterations from scratch, using my caliper for milimetrical measuring, resolving issues of design, hardness and stability. Also I...

https://www.thingiverse.com/thing:5398100 Improved/Compact Oreo knob for the Ender 3/Pro/V2/S1 encoder knob. Requires no glue. Fits onto the rotary encoder instead of existing knob to stay compact. 6/7/22 - Slightly reduced size of pegs,...