ender 5 s1 slicer settings 3d models

Locking bed leveling knob for the Creality Ender 3 S1/S1 Pro remixed from my larger 70mm Dia to the standard 60mm Dia. This design has snap features that keep the knob in place during/in between prints; so no more vibrating out of position or...

The Ender-3 S1 Pro normally comes with some extra hardware and the M5X50mm bolt is the same that is used to attach the uprights. It uses two (625 - 5mm x 16mm x 5mm) and two (685 - 5mm x 11 mm x 5 mm) ball bearings. The 625 bearings are the same...

**Note 1: this is only suitable for feeding filament from the left side of the printer.** **Note 2: this is designed for the Ender 3 *S1* model. I doubt it will fit any other model, except perhaps the S1 Pro.** I printed the arm with supports. The...

(Will not fit Wyze Cam v2 or older models) Mount fits the left side of the machine, can be flipped before printing if you want it on the right side (Have not tested or looked into it). Print Settings Printer: Ender 3 S1 Pro Rafts: No Supports: Yes...

I made a thin, sleek, minimal and sturdy vertical PITFT50 V2 display mount for the Ender 3 S1 and S1 Pro without the Raspberry PI in the display casing. My Raspberry is laying behind the printer. You can print the Display_case and the...

A remix of the sunlu s1 dryer mount by hajo_s to It now fits ender 3 style printers or any printer that uses 20x20 extrusions. The angle on the original design was also to steep so the filament role did not ride on the roller but rubbed against the...

A remix of the sunlu s1 dryer mount by hajo_s to It now fits ender 3 style printers or any printer that uses 20x20 extrusions. The angle on the original design was also to steep so the filament role did not ride on the roller but rubbed against the...

90 degree top mount arm for Ender 3 S1 (Pro) with holes spaced for Djngnear's Sunlu S2 filament dryer tray.  While not required, I also recommend using the Sunlu S2 reverse bowden adapter by Martin_au to complete the setup.All holes are sized to...

... sided tape for attaching to the stock E3v2/Pro QR covers. This is meant to go with wojtaszek632's Ender 3 v2 X tension housing S1 style https://www.thingiverse.com/thing:5359174 as their QR cover doesn't have clearance for BL/CR touch sensors.

Printing Temperature: 300˚C Bed Temperature: 60˚C Printing Speed: 50mm/s Fan: OFF Direct Drive: Retraction Distance: 3mm Retraction Speed: 40mm/s REMIXED FROM: https://www.printables.com/model/417892-ender-3-s1-pro-heating-bed-cable-chainholder...

Y-Axis Stepper Motor Mount for the Creality Ender-3 S1 and S1 Pro This makes use of the spare "z-axis end stop" included with the printer. ...The regular y-axis end stop has no mounting holes in the pcb and is a flawed design for silent operation.

... adapter / mount for my s1 pro. ...Used [Ender 3 S1 Pro C270 Z Mount](https://www.thingiverse.com/thing:5787810) as a base. ... Using it in combination with [HyperCube Evolution: Logitech c270 webcam mount](https://www.thingiverse.com/thing:3789929)

This is a 5015 circular fan duct upgrade to Creality's ender 3 S1/Pro or  Creality's Sprite extruders.Here is it in action: ChangeLog-Fixed mounting Issue-Better Airflow-Added new mounting points for more rigidity-added overall...

Tool holder for 3D printer Creality Ender 3 S1 pro. ... -1x slot for filament cutter -2x round slot Ø 11 mm -1x round slot Ø 7 mm Attention the tool holder replaces the slot for the control screen.

I aimed to use the right front corner of Ender 3 S1 pro printer to mount the sd card holder. You can use the existing two bolts on the corner. ...Better print with support enabled.

I wanted a simple snap on filament guide for my Ender 3 S1 pro. ... Remixed this from: https://www.thingiverse.com/thing:4428057 https://www.thingiverse.com/thing:5419960 Needs support for the hole

Simple holder for Logitech C270 web cam for the Creality Ender S1 Pro. Place the model as you like. Brim and supports are needed. ... 20mm M3 screw and nut is needed for mounting.

This is the right (switch) side for a replacement for the stock ender 3 s1 pro light or the light kit. ...Original model at thangs.com: https://social.thangs.com/m/974694

I have designed a new snap to work with the leveling wheel 5908385. ...This Snap works with Ender 3 S1 Plus. ...It is a bit of a work in progress but it does work as it is.

Ender 3 S1 Pro THERMOSTAT MOUNT Printing Temperature: 233˚C DON'T RUN OVER 245˚C It'll Start Smelling Like Breakfast Bed Temperature: 60˚C Printing Speed: 50 - 60mm/s Fan: ON FULL TILT

Remix of the Ender 3 S1 Tool Holder, with space for nozzles and nozzle wrench. An additional holder for a pair of long nose pliers. This is a work in progress. ... Feel free to remix as desired.

Remix pour le nouveau chariot de l'ender 3 S1. ...Apres plusieurs essais, je suis parvenu à ce que les crans fonctionnent réellement, je recommande neanmoins d'imprimer les dernieres couches en 0.10 plutot qu'en 0.2

Ender 3 S1 extruder wheel geabox fo Taurus. ...Looks cool, but a bit noisy.Still in progress and can be changed at all.You need 2 pinsTaurus cooling system - thingiverse.com/thing:6037984Video - https://youtube.com/shorts/ljr8Pbum4LY

The stepper motor cover for MrPiouPiou's bed cable angle adapter doesn't clear the bed on my Ender 3 S1 Pro - just not enough clearance. This causes the bed cable to catch on the gap in the corner of the stepper motor in the back. To solve the...

Scale a little to get the best and snuggest fit!This works great when combined with:Ender 3 S1 Secondary Spool Holderhttps://www.printables.com/model/158734-ender-3-s1-secondary-spool-holderThis model is on the idea of:Your Color Change Buddy - dual...

Scale a little to get the best and snuggest fit!This works great when combined with:Ender 3 S1 Secondary Spool Holderhttps://www.printables.com/model/158734-ender-3-s1-secondary-spool-holderThis model is on the idea of:Your Color Change Buddy - dual...

A brush holder to automatically clean the nozzle with, for creality Ender 3 S1 and Ender 3 S1 Pro printers. ... Made a detachable brush holder, so I can add different size/type brushes or perhaps if I need to switch it up later with a PETG print if I...

This tools support enable to get scrapper and cutter on top of right pilar of Creality Ender 3 S1, without any impact on Z axis move capability.---Ce support d'outils (cutter et spatule) se positionne en haut du poteau droit de votre Creality Ender 3...

Ender 3 S1 PLUS Rear Y Axis Cable Chain Mount // Ender 3 S1 PLUS Rear Y Axis Cable Chain Mount (18x) For the chain links used here https://www.thingiverse.com/thing:2920060 (1x) Female to female coupler mesh used this one...

CREALITY ENDER-3 S1 PRO - EXTRUDER FAN COVER Creality Ender-3 S1 Pro Upgrade and Modification, enjoy our Version. If you have any Questions, just write a CommentDISCLAIMER This Product may only be printed for Personal use and may not be Sold...