ender 5 x axis 3d models

After the installation of linear rails on my ender 5, the y-axis belt fixation on the gantry sits a lot higher above the 2020 profile. Because of this, the tension becomes higher when approaching the sides of the bed because the gantry gets more...

X-axis top entry robot

X-axis top entry robot

Mendlemax 1.5 Spool Holder Alignment along X Axis Aligning the spool direction with the X-Axis makes printing easier by keeping it straight and preventing filament bends at the spool. ... Additionally, you will need some spool rolls to get started.

I designed these clips to enhance the Z axis tensioner's ability to prevent table drop when the steppers are turned off on my Ender 5. They closely resemble bowden clips used on extruders and hot ends, but with a few key differences. These clips are...

Designed some 3D printed Oldham Couplers for my Ender 5 Plus. The ones available didn't match up with the bolt pattern on the 5 Plus' lead screws. Suggest Printing at 100% infill with 0.12 layer height and 4 walls. ... Uses M3x8mm to attach to...

The ones available didn't match up with the bolt pattern on the 5 Plus' lead screws. Suggest Printing at 100% infill with 0.12 layer height and 4 walls. Uses M3x8mm to attach to brass nut and M3x10/12mm to attach to Z Gantry Bar. Print Settings...

It also adds more body to touch the X axis plate without the need for spacers or extra hardware to fit between and keep it more robust with less flex. Get other parts from the original thing. ... Compatible with: X:...

Background ========== I sought a stiffer, more impressive X axis for my Bear printer with a more durable idler. Like the Serious Business y-axis replacement, this one employs external bearings in the idler. Also like the y-axis it uses press-fit...

My Shapeoko 5 Pro showed up with a cracked, bent and warped X axis drag chain mount. This is a (close enough) matching part that fits as a drop-in replacement with the regular screws. The standard screws are threaded for M3, I recommend heat...

My ender 5 plus factory spec out the box has this additional dampening bracket. Which needs slightly more space for the cover to fit properly. Test prints fit perfectly. Use the same fastening / fixtures listed in the original. ...Worked a treat.

This new component serves as a substitute for the original Y-axis limit switch holder.

1 x 330mm MGN9H for the X 1 x 350mm 2020 T slot extrusion for the X I got a 1120pcs Hex Socket screw set and some T nuts You do loose about 20mm in the Y axis, but have designed a linear rail conversion for the Y axis that should regain that. Ill...

The other Z axis stabilizers didn't work for me, so I made my own. ...I use 608 skateboard bearings.

This thing was designed to upgrade Taz 3s to Taz 5s, replacing the x axis mount plates found on Taz 4, 5 and 6 machines. We created it because the original mounting plates were laser cut acrylic plates that couldn't be bought anywhere. For a year...

I needed just a 2mm extension because for some reason my y-axis was grounding out further into the build area than the designed parameter.

Just a little cap to cover the Y axis switch pcb when using D_Jespersen's belt covers.  I printed it upright because it's a small enough space to bridge. ... Snapped right on, first try.

This is a budget-oriented dual z-axis modification for an Ender 5/5 Pro. I designed it with the goal of limiting the amount of non-printed components required for the build to keep it budget friendly while still being a dual motor setup. It is a...

... with a fresh spin. ...I managed to snap both original pieces in two while attempting to put them together. So I turned the print orientation by 90 degrees, and that gave me significantly better stability in the crucial areas around the z-axis.

I've compared it to the MK2.5 Carriage of the Bear X-Axis v0.6 and noticed some minor differences in the alignment of the Cable Bundle and Endstop Trigger. This could cause the cable bundle to collide with the frame or electronics housing and...

I've compared it to the MK2.5 Carriage of the Bear X-Axis v0.6 and noticed some small differences in the aligning of the Cable Bundle and Endstop Trigger. This could make the cable bundle colliding with the frame or electronics housing and prevent...

Convert the Mendel Max 1.5 to feature a vertical X-axis by installing an x-ends system with a focus on utilizing 10mm Z-axis rods and 8mm X-rods, as well as integrating two Recreus extruders. Alterations to fit specific extruder requirements can be...

Install them first and then feed the belt through from the bottom, securing it with two M3 x 12 screws and two M3 nuts. Updated July 28, 2019: Significantly reduced in size, requiring only two screws per installation. ...Added nut pockets for added...

You must use this mod https://www.thingiverse.com/thing:3890803 to raise the 5 plus bed up to make clearance for the bracket that connects the belts to the bed and make room for the top pulley bracket. Z movemet will be reduced to about 370mm. I...

Looking for a suport for the webcam for my Ender 3 v2 many good ideas, and many good designs can be found, but I look for a easier and simple one, so decided to do this. It is easy to print, fits perfectly at the X tensioner so follow the Z...

This clip allows for mounting a single 5 mm LED onto the X axis of a FlashForge Creator Pro, Dreamer, or similar printer (anything resembling a Replicator). When using a high-performance narrow-beam LED like a Nichia NSPW500GS-K1 driven at 20 mA,...

Creating the X-axis for a CNC milling device initially involves designing it with measurements approximately 300 by 950 millimeters.

Needed a Cover for my X-Axis Board because I had to flip the Endstop Sensor and the original Cover was too long and wouldn´t sit properly because of the Sensor and the Fan was hitting the original Cover. This was designed in Fusion 360. First attempt...

This is a basic clip that allows to mount a single 5 mm LED onto the X axis of a FlashForge Creator Pro, Dreamer, or similar printer (anything vaguely looking like a Replicator probably). When using a high performance narrow-beam LED like a Nichia...

Machine Axis X is fully operational now. ...Please don't forget to output EIXO-X-LD alongside any physical assistance provided.