ender v2 filament guide 3d models

make a pin (cut a piece of 1.75mm filament to secure the pin) to replace the M4 bolt. ... also use the 608 bearing from https://www.thingiverse.com/thing:3002837 08/19/23 add a V1.2 for low mount filament. ...(https://www.thingiverse.com/thing:2948891)

Insert the aluminum base and click your guide in place for a quick setup. Version 3 Offers Optimized Performance with No Ring Print Issues at Any Resolution. If Your Printer Struggles to Bridge, Print End Clip with Support Lines at 1.8mm Apart (5...

... ..... ... I moved the opening to the far end of the guide, instead of on the side of it. ... I also extended the feet/arms/tabs of the Attachment, as the original one had the habit of falling off, as it slowly worked its way out of the 2020 extrusion

... to having mounting screws etc and the thread screw supports in place, I was only able to extent one single arm. However, doing so has had a dramatic effect on the stability of the guide. ... The arm its self remains untouched as per the original.

Designed this to stop my filament rubbing against the extruder mount and cables, I'm mounting it on my Lack enclosure underneath the printer so it used to rub there. ...Remix of timqui's great design!</p>

I needed to prevent the filament from coming into contact with the lead screw, so I opted to design a solution. ... To achieve better fitment, I decided to enlarge the bolt holes compared to my initial print.

... wise you should orient the dove tailed bracket so the the dove tail is on the bed and the pillars are facing upwards for the best quality. Printed on my Ender 3 Pro in PETG. ... Thanks to AlexanderGi so the dove tail bracket and the main arm.

... * Two 5mm ID x 1mm thick Shims - Find them at https://openbuildspartstore.com/mini-v-wheel-precision-shim/ The shims can also be printed. Holder V2 has a 4.5mm pass-through hole to eliminate fitment issues. ...Holder V1 is 4mm.

The goal is to stop the filament from coming into contact with the spindle of the Z axis. I have utilized PLA and the friction is more than adequate. ...In my instance, a layer height of 0.1 was assigned, although such a high resolution is completely...

Note: I used the same bolts and nuts that are installed in the original spool (I removed de original spool as upgrade, but purchase the same bolts and t-nuts and you can install it) and to install you need to remove the side small cover of the rail,...

If I had this feature from the start, it would have prevented issues with the extruder slipping during prints, which was often caused by filament removing grease from the z-axis screw. ... To help me further, please follow me on Instagram at @code4kidz_...

The size was increased, the thread feed channel was significantly deepened, and the angle was made sharper, which made it possible to solve the problem of the filament jumping off the wheel.The frame has also been updated, the upper channel (width)...

... which I built upon by incorporating these enhancements. A quarter-inch diameter bolt is used, but any similar-sized bolt with a smooth shank will suffice, provided it covers the area where the filament touches and remains smaller than the hole.

Filament Thread Guide V2 For Disco Easy 200: This Model Features A Self-Supporting Ring Design.

...... I wanted something quick and easy to add and remove the filament. There is a long model and a shorter one. For the spring I used a standard paper clip straightened out with no bends or kinks, then tightly wraped tight around a 6.5mm drill shaft.

Remixed from https://www.thingiverse.com/thing:4821339 Loved the design, but I had no need for the Z axis guide. ...I used this on an Ender 3 Pro, not a V2, so I removed the text as well. ...Prints easily with no supports required.

A bearing Filament guide for the Ender 3. Designed by Sam Whitehouse (author) and uploaded by me by request from the author. Two bearing base are available one with a bearing cap hole and one with out. If you printer has perfect tolerances you may...

Filalment Guide for Ender 3/Ender 3 Pro I design it because I didn't find any one that fit as well as I wanted.

... fan. ... So I designed this guide to get more airflow to the heatsink itself while using the original cover of my Ender 3 V2. Tested with a printing temperature of 230° without clogging. Works with 40x10mm fans. ... Printed in PLA without support.

I wanted a movable guide for the filament on my Monoprice Select Mini V2. I have printed and used the small guide with the movable guide bushing quite successfully, but wanted something with more than one screw hole holding it to the printer. The...

A Custom Filament Guide for the Ender 3 Printer. Designed by Sam Whitehouse, this bearing-based solution was made available by request from the author. There are two base options: one with a bearing cap hole and one without. If your printer has ideal...

Drawing inspiration from an earlier design not compatible with the V2 as-is, I devised a solution: inserting a short segment (40-50 mm) of Teflon tubing into the feed hole to facilitate smooth entry into the filament guide and maintain the filament's...

V2 3D printer's filament guide mounts onto Z axis rods, improving stability as it directs the filament over the extruder. This prevents snags on spools, reduces tension on feeders and minimizes jams, resulting in a neater look. ...Enjoy your improved...

Filament Guide for Creality CR-10s Pro v2. ... I used this bearings: ...

... guide to the printer frame. The following filament sensor can be purchased on Amazon: https://www.amazon.de/gp/product/B07FSXFPLD This part works great together with the following filament path guide: https://www.thingiverse.com/thing:3061551

Guide filament into your CR-10S Pro V2 (and possibly other Creality line of printers) with this little doodad for less friction and chafing caused by the filament detector's sharp chamfered edge. Prints in no time at all, snaps right into place. Some...

Guide filament into your CR-10S Pro V2 (and possibly other Creality line of printers) with this little doodad for lower friction and chafing caused by the filament detector's sharp chamfered edge. Prints in no time at all, snaps right into place. ... ...

Guide filament into your CR-10S Pro V2 (and possibly other Creality line of printers) with this little doodad for lower friction and chafing caused by the filament detector's sharp chamfered edge. Prints in no time at all, snaps right into place. ...

Filament guide for filament entering the lack enclosure The bearing used is an NTN 6000z bearing.

(*video) English: Filament Guide for Creality Ender 3 printer! (In the Post-Printing section, there are pictures and videos on the help picture, (marked in the text)) Required: -2DB M5 T-Nuts (A spare is provided for the printer) -2 pcs M5x8...