ender v2 leveling 3d models

Updated the mounting section with a boolean cut to accomodate the z-screw brass mount, which on the Ender 3 V2 is protruding of about 1mm. Also gave slightly more room for the z-screw itself. ... Added a second design, without the z-screw protection,...

Extension feet for Ender 3 Pro/V2 with useing original rubber feet as rubber inserts. Supports needed only in place for rubber inserts. ...Use two M3X20 bolts with M3 T nuts (or print M3 T nut inserts for regular M3 nuts) to secure the feet to the 4040...

This is a replacement drawer knob for the Ender 3 v2 drawer. I suggest to print in PETG since it is more flefible and PLA will break when you push it in the hole of the drawer. Category: 3D Printer Parts

Just another filament guide for all Ender 3 models including Pro & V2. Looks similar to the existing guides like 3059604 from MattEllison, but this one slides smooth into place and rests flat on the top rail. To ensure proper printing you should...

My PS Eye mount for Ender 3 v2. There is no need for screws. It slides right to the main 4040 profile of the base and the camera goes on the top of the mount. ...The camera base should slide right into the top of the mount and happily sit there.

Hotend cover for Ender 3 V2, printed for reason to replace standard cover and fan. Can mount 60x60 fans with dirrerent width. Mount with three standatd M3 screws and need one M3 nut. ... Need some hand work to align with roller M10 nut.

This very simple clamp slips over the spool holder that comes with the Creality Ender 3 Neo V2 to prevent the spool from sliding off. Leaves just a little space between the end of the spool and the filament to allow the spool to spin. ... Inside...

I made this mount specifically to fit Creality Ender 3 V2 Neo. The camera I have mounted is the "Creality Camera" but you can mount any that fits dimensions. If you need it the part printed for any reason. ... Message me at through my Etsy account...

I really liked the big rollers for the Ender 3 V2 filament guide, but I needed a more flexible setup where my spool holder could be mounted on the side of the printer, needing a double roller setup. ... (Use the bearing guide/rollers from the original...

I wanted to make My Ender 3 v2's z axis double. So i needed a part that hold second Z axis motor. This is the original parts 3D design. ... You can write me if you want to improve the parts.

Made some slight adjustments to the hole placement to allow fitment onto the Ender 3 Pro V2 as the mounting plate is slightly different. I filled in the screw access hole that was on the front too. ... Simple screw into the bottom left (as...

Replacement knob for the ender 3 v2 LCD. The original is small and flat, I needed something knurled, a little bigger and with a spot for the finger to rest for quick turning. Prints well upside down, shouldn't need support but just in case you...

Mounts to the M3 holes on the Ender 3 V2 X-carriage, with the same probe offset as the classic mount by Jkostenov. Fits with the stock fan duct as well as the Mini-Me V4. Probe offset: X-42.00 Y-10.00 Thanks to Jkostenov for creating the original,...

... the way, so I made this. ...It is mountable on the Ender 3 V2, and I'm not sure about the pro. Definitely not the original, though. It is made for the raspberry pi 4b. ...Thanks to https://www.thingiverse.com/thing:4665097/ for making this originally!

Mounts to the M3 holes on the Ender 3 V2 X-carriage, with the same probe offset as the classic mount by Jkostenov. Fits with the stock fan duct as well as the Mini-Me V4. ... <strong>Probe offset: X-42.00 Y-10.00</strong> <strong>Thanks to...

Hi everyone, I wanted display on my Ender 3 V2 on the left side and because I didn't found any good I decided to design my own. It's easy to print. Display is in 45° tilt and for mounting I used screws from the original one. ... If you have any...

Fits very tightly on the lower 40mmx40mm rails of the Ender 3 v2. Provides a "shelf" to support the wires and gives you something to tie wrap to. STL file contains left and right facing brackets. ... Print both or delete the one you don't need in...

wire support for my ender 3 v2 direct drive, mounted to the top of the enclosure and use a auto retract keychain inside. ... https://www.amazon.co.uk/gp/product/B0995YK84C/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1 key chain used, just trim the...

Hello, after a difficult job, I present the first Mistral Fan mod for Ender 3 V2! ... Very easy to install especially if you use my ratchet screwdriver ;-) https://www.thingiverse.com/thing:4853538 Plug ang play No modifications Recommended abs 20%...

The title says it all! ... This is a mount I designed to hold a Wyze Cam V3 on an Ender 3 V2 to view the bed as the printer is running. ... The design uses 2 M4x8 bolts and 2 t-nuts to screw the mount into the side 4040 extrusion.

Screen wire protect, use with ENDER 3 V2 LH SCREEN MOUNT_REMIX (https://cults3d.com/fr/mod%C3%A8le-3d/outil/ahuczekdesign-32ca). You have STL and Fusion360 file. You can change parameter in Fusion360 to change anything. Print face to bed, and use...

... .. ...the stock ender 3 v2 spool holder is a friction monster and causes all kinds of under-extrusion problems. So here is my Brachiosaur-like spool-holder that uses 2 skate bearings. Works well for me. Hope you like it. ...Will be uploading pics soon.

Ender 3 V2 better Motherboard Case This motherboard case has a sliding lid that is on the top of it, in this case there is enough room to fit the motherboard and two buck converters for noctua fans or anything if there is anything to update on the...

This is a bracket for the orbiter v2 to mount to the ender 5 with a e3dv6 hotend. It is designed to accommodate the generic e3dv6 adapter and the 3010 parts cooling duct. ... x_offset: 25.42 y_offset: 28.51

... with the Aquila. ...I think the Ender 3 V2 has similar ones. Found the file at https://www.thingiverse.com/thing:4737883. ... It printed great, but I wanted a slightly tighter fit and I made the slope steeper to the tools aligned closer together.

RbPi holder for Ender 3Pro/v2 Remixed dual-sided SD slots, and enable screw holes to print without support. ... Compatible with 9cm * 6cm cases like this one in the link below: ...

... contribution. ...:) I made a IKEA (Type: L1324, 21777) LED-holder for Ender 3 v2 that slides nicely in to the V-frame. Brims was necessary or else it popped of from the bed. ... If anyone has tips and trix to make it better, please let me know.

Fits very tightly on the lower 40mmx40mm rails of the Ender 3 v2. Provides a "shelf" to support the wires and gives you something to tie wrap to. STL file contains left and right facing brackets. ... Print both or delete the one you don't need in...

#### CR Touch Mount for the Satsana Remix for the Ender 3 V2 I couldn't find a remix for the CR-Touch so I created it myself. #### Why? ... Because the original mount didn't have room for the connector of the CR-Touch, and if you tried to put the...

This bracket slides onto the side extrusion on the base of the Ender 3 v2. The original spool holder attaches to the top with the original t-nuts. ...This removed the weight of the spool from the top bar and places it much lower down.