ender v2 leveling 3d models

This bracket replaces the current one supplied with the Ender 3 v2. It uses two of the three original T-nuts to mount in the same location, but allows the screen angle to be adjusted to higher or lower angles. ... Print this face down with supports for...

This are feet designed specifically for the Ender 3 V2's blocky rectangular rubber feet. Print 4 and set your printer on top. Provides heavier dampening than your standard squishy tennis ball looking feet. ... Print with 100% infill with TPU 95A

Minimal size case to install a raspberry pi into an ender 3 v2. ... The clips have no margin, so you will have to move each side in and out a couple times before fully inserting it, otherwise it can get stuck x)

Fan shroud/hot end cover for ender 3 v2 neo with lightweight fan holder for spider hot end. This one: https://www.thingiverse.com/thing:6029098 Needs 1 m3 heat set insert for the screw hole. ...Painted the "Y" design on the front red to make it...

This is a divider that will fit in the larger section of the drawer under the bed of a Creality Ender 3 v2. Each segment has it's appropriate size etched into the bottom. ... Remixed to fill the entire length of the drawer, and not knock the handle out...

a simple camera remote holder for use in timelapse videos that i made to attach to Ender 3 V2 using existing hardware screws. ... used a cheap blue tooth camera remote from amazon (link below) ...

... but bltouch will be mounted 3mm higher. ... Original worked great with stock Ender 3 v2 hotend, but I replaced it with all-metal one which is slightly shorter for some reason and bltouch probe collided with bed.

For designers to make custom print head and other mods for the X carriage assembly on the Ender 3 V2 Neo. Update 2-16-23 3PM PDT: Corrected the position of the upper left V-Wheel, was off by 4mm. Added a missing hole at the top right of center on...

This is a remix of:Ultimate Ender 3 V2 Nozzle Brush I've tweaked it so that you can print it without the supports and secure the brush with zip ties.Also, I lowered it a little because it would smash into it if you had ABL and did G29.

A direct drive mount for Ender 3 V2 with adjustable X and Y axis. Made it adjustable for my dual gear extruder and possibly for other upgrades. ... Important note: make sure that X end stop is triggered, if not, add some spacer or bend the metal...

I moved some of the holes to better fit my Ender 3 V2, and cleaned up some of the mesh. ...This should fit the Stealthburner as of commit aabd953 Updated Jan 9 2022 to fix hole location Stealthburner link: ...

I haven't found nut that will fit my threaded lead screw in ender 3 v2 so i designed my own. On photo is version V1. V4 should be more easy to put in. if you have PETG print in PETG! ...I printed in cheap PLA for test.

Remixed version of the double led strip for the Creality Ender 3. Used this on my V2. Made the distance between the led strips a bit bigger to better spread the light on the print surface. ... Used the following led strip: ...

These are direct drive mounts for Ender 3 V2. These mounts are for the default hot end. One is for the default single gear extruder and the other is for the dual gear extruder. ... To install, remove the spacers of the rollers, then fix the mount...

Bottom Filament Guide for Ender 3 V2 Neo. This is a remix of two designs taking the best element of each. https://www.thingiverse.com/thing:3010366 https://www.thingiverse.com/thing:4648991 PLA is strong enough. ... Carefully remove Z axis...

This is a Support for my Wyze cam v2. ... I made a support for Ender 3 s1 printer and a cage for the cam. I just glued them together. there's also all the files to edit them in case you want to. ...

This is a bracket for use when upgrading a Creality Ender 3 V2 Neo with a Titan direct drive kit. ...The bracket will attach to the two offset holes on the x axis motion assembly and will hold the CR-Touch device as well as the accelerometer that comes...

My Ender 3 V2 Mother board is on the top layer so the fan was at the botton with little to no air flow so I made a duel fan holder to mount on the side using the 20x40 extrusion as support

If you have direct drive and the extruder stepper space is empty, you can use this as a cable guide on your Ender 3 (v2). ... If your printer is inside an enclosure i advise to use heat resistant filaments like: ABS/ASA/PETG

to jest rmix z opcją czyścika filamenty żeby nie blokował łożyska link do czyścika https://www.thingiverse.com/thing:3033662 Ustawienia drukowania Marka drukarki : Kreatywność Drukarka : Ender-3 v2 tratwy : NIE Obsługuje : Nie ma znaczenia...

I needed a dual Z bracket for my Ender 3 V2, but without the need of extra hardware for mounting it. The only extra hardware needed is the nut for the leadscrew. ... The model is oriented so it does not need supports.

Side 220v plug for Ender 3 V2. Designed to place the printer on a narrow table or with little space. It consists of 3 parts to avoid having to print with supports. Then it is attached with glue. No need to modify any cables. ...The original screws...

A replacement knob for the belt tensioners of the Ender 3 V2. Or just an M4 knob for anything ;) Requires a M4 melting winding brass insert (see image) using a soldering iron. ... You might have to open the hole a bit after inserting the insert...

This cable chain mount screws into the Ender 3 V2 frame with M3 bolts. I designed it to be compatible with the common V-slot covers and also to be more in line with where the cables connect. ...Make sure to print it with the square part flat on the...

This is an adapter to be used with the original spool holder of Ender 3 V2. I have limited space above the 3D printer where the original holder is fixed. So, this thing could be used together original holder over a table. ...I'm using beside de...

If you have the Ender 3 v2 Adjustable Screen Holder or the remix, and your screen is loose, you don't have to reprint the entire thing again. Print 2 of these wedges and install then on the screen posts, behind the adjustable screen holder. ...If it...

This is a replacement drawer knob for the Ender 3 v2 drawer. I suggest to print in PETG since it is more flefible and PLA will break when you push it in the hole of the drawer. //edit: Makers stated, that PLA will work without issues, thanks for...

My PS Eye mount for Ender 3 v2. There is no need for screws. It slides right to the main 4040 profile of the base and the camera goes on the top of the mount. ...The camera base should slide right into the top of the mount and happily sit there.

Flipped case for the Creality Ender 3 V2 for better access to mainboard. First thing I tried to print in PETG. It's not perfect, but it is functional. Some parts got unstuck while printing, had to adjust 2 holes with soldering iron. 3x5x5...

Designed to fit Creality Ender 3 V2 Neo but can be used as standard container without attaching the rails. ... 2 container sizes (mm): 135L x 40W x 25H and 135L x 40W x 40H Caution: When used on printer, keep all items below build plate surface to...