endotracheal tube organizer 3d models
130145 3d models found related to endotracheal tube organizer.thingiverse
I developed this lid for the endotracheal tube to decrease the risk of contamination during endotracheal intubation, especially in patients with COVID-19. ...There are two versions: one completely closed and one with a 4.7mm introducer hole.
thingiverse
This is an endotracheal tube rack for tubing sizes between 10mm - 3mm in 0.5mm increments. Each slot is 2mm larger than the labeled size for ease of use. ...I have split the model into two halves, one with 10-7mm and one from 6.5-3mm for easier printing...
thingiverse
Endotracheal Tube Holder, FINAL DESIGN UPLOADED. Works well and can be used well. Need an elastic band or some sort of head tie so it can be wrapped around, use cotton pads or any foam to be attached to the cheek pads. ... GB
thingiverse
This endotracheal tube clamp could be used to prevent aerosol or droplet spread from an intubated COVID-19 patient. It was remixed from https://www.thingiverse.com/thing:4271154. 1. Detachable design. Now, in order to apply the clamp, you...
thingiverse
Endotracheal tube fastener : This was designed based around a request posted on 3D printing reddit page. All the measurements are roughly guessed after watching related videos on youtube. All the parts are designed to be able to 3D print So issues...
thingiverse
This is a disconnection wedge used as a lever on the 15mm male connector to disconnect the ventilator circuit connector from the attachments (endotracheal tube or tracheostomy tube) without pulling, pushing or twisting which may cause pain or...
thingiverse
Clamp Endotracheal tube with finger support Based on https://www.facebook.com/groups/clamporotraqueal/permalink/685648202014013/ but with modifications to the finger support for more area, better grip and fewer injuries. ... Work in tubes with...
thingiverse
This fixator can be used in orotracheal tubes so that after intubation, better stabilization is achieved, reducing the risk of involuntary extubation. It has been tested in tubes with the following measures: 5.0 ~ 9.5 I do not recommend using PLA...
thingiverse
I was warned that there was a shortage of these clamps in local hospitals. These clamps are used when intubating patients to prevent the spread of any infectious diseases they might have. <h3>Usage:</h3> If you are planning to use this device: ...
prusaprinters
<p>I was warned that there was a shortage of these clamps in local hospitals. These clamps are used when intubating patients to prevent the spread of any infectious diseases they might have.</p> <h3>Usage:</h3><p>If you are planning to use this...
thingiverse
This clamp can be used in the orotracheal tube to temporarily block air while health professionals are tubing sick people with COVID19 (Coronavirus), reducing the chance to get infected. It was tested with these dimensions (inner diameter): ...
thingiverse
Basic Infos / Remixing Just a simple design to organize your tubes in your fridge. Can/should be place in the fridge door. If you want to remix, make it bigger/smaller do so, the 3mf file is included. <h1>Important: </h1> The model has to be...
myminifactory
Intubation stopper for use with endotracheal tube in the medical process. ... Recommended filament: TPU (thermoplastic polyurethane) Measures: Large: 4.5mm diameter holeMedium: 3.77mm diameter holeSmall: 2.75mm diameter hole Creators: Rafael Taveira...
thingiverse
This are tubes for organizer all the mexican coins when you open the moneybox
thingiverse
Replacement cap for wall mount organizer. ... Tube diameter 16mm (0.63 inches)
thingiverse
PTFE tube comb to organize your PTFE tubes. Has a flat back so can be mounted with velcro or double-sided tape. Or just put it on the tubes to keep then neat and tidy. ...
cults3d
PTFE tube comb to organize your PTFE tubes. Has a flat back so can be mounted with velcro or double-sided tape. ...Or just put it on the tubes to keep then neat and tidy.
thingiverse
Another add-on to the SMD organizer tube design. I designed this to be abble to wall mount all the tubes. I choose to not use this option but to place the tubes in drawers. If someone does find this more usefull, two 7mm aluminium rods can be used to...
thingiverse
A simple base plate with cut outs to hold coin tubes for storing, organizing or carrying. ... Designed around Edgar Marcus Kointubes ( EMco) but may fit others as well.
thingiverse
A simple base plate with cut outs to hold coin tubes for storing, organizing or carrying. ... Designed around Edgar Marcus Kointubes ( EMco) but may fit others as well.
thingiverse
A simple base plate with cut outs to hold coin tubes for storing, organizing or carrying. ... Designed around Edgar Marcus Kointubes ( EMco) but may fit others as well.
thingiverse
A simple base plate with cut outs to hold coin tubes for storing, organizing or carrying. ... Designed around Edgar Marcus Kointubes ( EMco) but may fit others as well.
thingiverse
A simple base plate with cut outs to hold coin tubes for storing, organizing or carrying. Designed around Edgar Marcus Kointubes ( EMco) but may fit others as well. ... Holds x4 Large Dollar and 10x Small Dollar Tubes
thingiverse
Resistor (tube) organizer Pick your resistors into 14mm diameter tube. Put all tube into the "test tube rack" shape organizer. Enjoy your electronics works orderly. Require: [down10x_1.stl] x n [up10x_1.stl] x n [pillarx1_1.stl] x 2n [M3 nut...
thingiverse
This is an organizer for acrylic paint tubes, I bought a set of paints and didn't like the tray they were in. They just stand up and the cap fits in the hole. ... There are holes for brushes also.
prusaprinters
I made this print to organize the PTFE tubes from my buffer.Print on its side with no supports or brim. ...There's a bend variation included providing a gradual bend if needed.</p>
thingiverse
Simple shrink tube organizer, for tubes up to 1m length with bracket which can hold up to 5 individual boxes in one place. Each box can be removed from bracket separately. box has a screen to check if tube is not running out. No additional parts...
prusaprinters
This helps keep the 5 tubes spaced from the MMU2 unit Print instructionsThe curved bar is placed on one of its sides. ... You need tree of each part_nut and 3 of part_screw and then one organizer
thingiverse
An organizer for tubes of whatever. I carry them in my truck in a tote and was tired of them getting bent and lost under other stuff. This is an original design on 3d builder, I couldn't find anything I liked. Feel free to improve it. I tried to...