eppendorf 1.5 ml 3d models
1139286 3d models found related to eppendorf 1.5 ml.thingiverse
This Eppendorf/Centrifuge tube holder is used for packing under nitrogen - flow of nitrogen goes into a downward-facing funnel. I put my samples into the tubes, put them in the rack under the funnel, wait for a few minutes for nitrogen to displace...
thingiverse
I wanted a modular eppendorf rack that I could expand at will and where the modules could be snapped together to form large trays. Also I needed a simple tray with only two tubes in it that would go into a small vacuum chamber. I have tried to save...
prusaprinters
<p>Microtubes holder</p> Category: Tool Holders & Boxes
thingiverse
6 X 1.5 mL eppendorf rack. ... Useful for high school blood typing lab (A, B, AB, O, anti-A and anti-B).
thingiverse
Штатив для центрифужных пробирок Eppendorf объемом 0,5 мл на одну позицию.
thingiverse
We needed some new Eppendorf racks so I made a few and thought they might be worth sharing.
thingiverse
A sleeve to fit 0.6 mL tubes in 1.5 mL size centrifuge holes
thingiverse
This tube insert is used as an adaptor for a barocycler tube to make it compatible with equipment sized for a 1.5 or 2 mL Eppendorf tube. ...Can be used for tissue homogenization, centrifugation, heating and shaking.
prusaprinters
This tube insert is used as an adaptor for a barocycler tube to make it compatible with equipment sized for a 1.5 or 2 mL Eppendorf tube. ...Can be used for tissue homogenization, centrifugation, heating and shaking.</p> Category: Biology
thingiverse
Eppendorf tube holder for 12 1.5 ml tubes. ...There are no any islands, only perimeters, so, you can print it in less than an hour.
thingiverse
I designed stand for 4 oder 8 times 1.5 mL Eppendorf tubes and want to share them with you. ... Others can be designed and uploaded on request.
thingiverse
This is a tube rack that securely holds standard 1.5 mL and 2.0 mL tubes microcentrifuge tubes. I liked MS3FGX's microcentrifuge tube rack but found that when I pushed down on tubes to close them, it made the whole thing flex down and it didn't fill...
thingiverse
2018](https://www.nature.com/articles/s41596-018-0050-5) type ancient DNA extraction and single-stranded Illumina type DNA libraries according to [Gansauge and Meyer 2013](https://www.nature.com/articles/nprot.2013.038). The original design was...
thingiverse
2018](https://www.nature.com/articles/s41596-018-0050-5) type ancient DNA extraction and single-stranded Illumina type DNA libraries according to [Gansauge and Meyer 2013](https://www.nature.com/articles/nprot.2013.038). The original design was...
thingiverse
For a more fancy outcome, you can print the first two layers in another color. ... One rack of size 16x4 will cost you ~1.50 Euro of plastic. ... Make sure to print it with the springs facing down.
grabcad
Eppendorf PCR tube 0.5 ml (0030108035). ...The lid is not 100% accurate, yet the outer dimensions and inner dimensions fit very well to the actual tubes.
thingiverse
Штатив для центрифужных пробирок Eppendorf объемом 0,5 мл на 48 мест.
thingiverse
A holder for two tubes, either 15 ml Falcon tubes or 5 ml Eppedorf tubes.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=51874 Instructions Using the following options: Size = 0.15 Thickness = 2 Units = 0 Label = 1,5 mL Type = 0 Font = write/orbitron.dxf Conversion =...
grabcad
This is a solid model of the 2 ml eppendorf tube Modeled by Bobby Dyer a medical device engineer based in Boston MA Rendering and solidworks model
thingiverse
The usual way to centrifuge a 0.5 mL tube is to nest it inside a 1.5 mL tube, but I sometimes had catastrophic failures when centrifuging samples for long periods at high speeds; the smaller tube would twist inside the larger tube, its rim would get...
thingiverse
This insert will allow you to convert old pipette tip boxes into microtube storage holders for 20x0.5 ml and 20x1.5 ml tubes. ...The insert takes about an hour to print on my Flashforge Finder with no supports since it is completely flat.It's 2.5 mm...
thingiverse
By using this adapter you can put an eppendorf tube in a falcon 15 mL, you will say, what is the use? ...I use that with Frac-920 of AKTA purifier to have the liquid droplet in the middle of the tube and not just close to the edge of the tube (when i...
thingiverse
Basic tube rack. ...If u want adapt it to 15 ml falcon scale-up with 1.46% factor
thingiverse
This is a magnetic separation rack for two, four, six or twelve of 1.5- or 2-ml tubes. I was restoring an old BioLabs magnetic rack that felt apart. All measurements are based on it. Suitable for magnet of 12.7 mm in diameter and 9.6 mm in...
grabcad
The bottom of a small line inside denotes exactly 1.5 mL. The screws are proprietary. 9.6 mm diameter, 2.5 mm pitch, 3 revolutions, no taper. Profile is .25 mm x .5 mm. If 3d printing, print the tube right-side up, with minimal supports (the bottom...