esp32 cam home assistant 3d models

This is a small project to turn a "dummy-camera" into a working ESP32-CAM. There is also an article on the website of the german MAKE-Magazine: https://www.heise.de/ratgeber/ESP32-Update-fuer-einen-Kamera-Dummy-4945742.html 01.12.2020 UPDATE:...

(Imported from Thingiverse)A case for the ESP32 Cam board that has no lid, the board snaps in with little force. It has 3 mounting points, with 2 holes each. There is a version for M1.5 (1.75mm) and one for M3(3.25mm). The holes are 14mm apart. This...

I first swapped out the Raspberry Camera for an "ESP32 + cam" module. After reprinting it, I discovered that the original design wouldn't fit my BIBO 2 printer because it was too thick in front and blocked the rear vent, and also too thick at the...

The original [ESP32 Cam housing](https://www.thingiverse.com/thing:4192843) design was very simple and compact. So, starting with that design, I added - Top: Micro-SD/TF card slot - Top: External antenna - Bottom: Access to reset button -...

Die kleine platte dient als kurzschluss schutz zwischen dem ESP32 Board und dem darüberliegenden FT232RL Modul

This remix does not require supports, though if using the version with the tripod hole on the bottom there is a little bridging but nothing to challenging. Rather than solder the wires to the ESP32-Cam I wanted to use Dupont connectors to make...

This is a simple camera mount for ESP32-CAM. It can orientate any position and wall mount or flat surface mount. V2 is a ring more, that you put before on the base, after you connect the case, and finally put up the ring to straighten! So no more...

This housing is designed for the ESP32-CAM including ESP32CAM-MB und an optional external Antenna. I just use them for the Prusa Connect integration.While I wanted to make the housing as small as possible I kept the hole for the Micro-USB connector...

I made some changes and improvements to DSK001's ESP32-Cam case that he designed for Alien3D's January 2021 UFO Project. Changes made: I made the button parts thicker, which means they print easier and they don't have to travel as far before they...

Two inner case variations exist: esp32-cam_front_with_cable is designed for heavy-gauge USB cables soldered directly onto the top of the header pins, as illustrated in photos. A weatherproof outer case, semi-rainproof housing, accommodates either...

ESP CAM HOLDER FOR BOX https://www.thingiverse.com/thing:3652452

I print with supports on so remember to remove the tiny support inside the case or the PCB will not fit inside. There are 2 versions of the inner case, one called esp32-cam_front_with_cable is designed for a heavy gauge USB cable soldered to the top...

The original mounts will work OK but I thought there was too much "flex" when rotating over the ridges of the ripple washer.* This “Thing” is an enclosure for an ESP32-Cam module. The design provides options for a Micro USB or JST-SM power...

One of the annoyances I've discovered with ESP32-CAM boards is that the cameras are not uniformly aligned; what is “up” for one unit is not “up” for another.  This in turn has made getting a case I like difficult.  So I made my...

So I designed this case to hold an ESP32 Camera, a 10x30 Radial Fan, and an external antenna. The back has a ball fitting for an articulated arm or whatever fitting you figure out. You can print without supports, or use small ones for the...

The first design holds the ESP-cam and the second the ESP-CAM including the adapter. I used the second design and it works great. ... The taller design allows to plug the USB cable underneath while the other will require solder connections to the...

This is a remixed case from @MAHAR4JA I need the Case with Flashlight hole and another alignment. ... With the adapter, mount the cam vertical and use every angle to adjust.

ESP32cam can be used with Octoprint and Mainsail Rotate the lens to adjust the focus. ... Mounting Screws & Nut M2.6x10mm x1 My blog post with ESP32cam installed on kingroon kp3s https://3dpmisosiru.blogspot.com/2023/01/klipperesp32-cam.html

Esta va entre la parte delantera y la plancha, usar pegamento y guias de filamento, un poco largas para una vez soldados los cables sirvan para encajar con la parte trasera La alimentacion del servo de la cabeza va puenteada dentro de esta con la...

<p>I designed this box to watch the timer of my washing machine. ...I run the example code from the library with the cam server.&nbsp;The batteries in a separate Box.

To fit my Cam-Module from DM (diymore.cc), I moved the camera hole 2 mm outwards and the light hole 1 mm inwards. SD-Card slot is optional. The back was modified to hold my different USB-board (see picture). Design changes were made with fusion360. ...I...

The Ender 3's lid features a hole where you can plug in an ESP32 board for power from a five-volt supply. Keep in mind that some users may need to enlarge certain parts due to tight tolerances. ... As shown in the accompanying picture, the mounting...

we can operate any kind of electronics applications using this relay module and ESP32

Designed from https://www.thingiverse.com/thing:4192843 for making an "All sky" camera, with an ESP32 cam (remove the lens of the OV2640 before, it's a bit tricky, be careful to not break it). I'm currently testing an Arduino-IDE program to enable...

... needs to be soldered in place on the PCB! As shown in this tutorial: https://randomnerdtutorials.com/esp32-cam-troubleshooting-guide/ Tutorial Overview: https://makeradvisor.com/esp32-cam-ov2640-camera/ Have fun, like, and share your Makes... ... SG

we can operate any kind of electronics applications using this relay module and ESP32 Print instructionsCategory: DIY Summary we can operate any kind of electronics applications using this relay module and ESP32 Print Settings Printer: Hacker x...

ESP32-CAM Housing with PIR Sensor More information can be found at my other ESP32-CAM housings: * https://www.thingiverse.com/thing:3815069 * https://www.thingiverse.com/thing:3949787 Shopping List/Einkaufsliste: * ESP32-CAM module:...

... which is a direct evolution of my first Micro Robot Camera! Comes with the source code ( Arduino IDE ). The list of parts and a tuto on MaxCraft3D.com ! https://maxcraft3d.com/fr/modeles-3d/proto-block/tank-cam-v2 https://youtu.be/W8hgNFMhnWk

A case for Raspberry Pi 4 with 80mm fan hole, i glued the fan i place with some hot glue. ...I used following fan: ...