esp32 case 3d models

ESP32 Cam Development case The case printed with transparent material, so no LED hole is needed. It is easy to access the pins, the reset button on the back of the board and no double sided tape is needed for the camera. ... 3 pcs half-round m3 Allen...

... 3D Printer?  No Problem!  I'm selling the ESP32 D1 Mini case in my Tindie Store. Updates:08/17/2022: Increased the amount of material around the cutout for the USB connector.09/09/2002: Added a new variation with the Espresense logo.

Simple case for the ESP32 S2 Mini module. I use this for ESPHome GLOW monitoring, so there is a hole in the top for a standard 5mm LED. Cable access and ventilation holes are provided. ... Everything is friction-fit but you can add a drop of CA if you...

Gehäuse für einen ESP32 als N64 Wireless Empfänger.

ESP32 with dht 11, can measurement humidity and ambient temperature

DIY Case for ESP32 V1 DIY board by AWOK, to be used with board from [AWOKMUSIC](https://awokmusic.square.site/shop/electronics/3?page=1&limit=60&sort_by=category_order&sort_order=asc) Holes are made for 4 14mm m3 screws *Be sure to double check the...

This project case was designed specifically for one of the ESP32 microprocessor development boards - the Lilygo T-Display. It works perfectly for me, and so I wanted to share. This development board is powerful (contains two microprocessors) and...

ESP32-CAM WROVER用のケース * 更新履歴 * 2023/08/27 ESP32-CAM1_WD_Body.stl LCD確認用穴追加、タクトスイッチ穴位置微調整 * 2023/06/08 STLファイル名統一 本体のガイドレールが基板と干渉して蓋が完全に閉まらない場合がある対処(ESP32-CAM1_WD_Body.stl) * 対応機種 * Freenove ESP32-WROVER CAMボード...

... of the PCB, and added a slot for the camera so it can slide on to the PCB. I also made a version with a connector for Jack's excellent articulated arm (12mm version). The 18650 battery shield was bought here and the case design is by Dust.

Snap-in enclosure for plain ESP32 DevKitV1, I have used this for ESPresense, ESPHome AirThings BLE, ESPHome Bluetooth Proxy ..

I made this case for an inductive energy monitor.The case is divided into three parts and also has plastic part that makes the ESP32 and PCB stay in place.The case snaps shut without any fasteners. ...Screw holes are provided as a an added security...

A simple housing for an ESP32 controller, comes with 2 flavors with the diffrence being one has a "tunnel" open up to the lid and one only has a hole for the cables to run through.

PARTS NEEDED:AWOK ESP32 V4 BOARDM3 10MM X 4PCS*I have found I get the best results with no part cooling for the first few layers to avoid edge warping, personally I don't cool for the first 8 layers.

 It holds an ESP32 development board and a 5.5 x 2.1mm power barrel connector from Amazon to power LED ws2812b strip lights.  I made it big enough to hold the ESP32, a barrel connector and 3 Wago wire connectors. ... I printed it in PLA with 3 walls on...

 It holds an ESP32 development board and a 5.5 x 2.1mm power barrel connector from Amazon to power LED ws2812b strip lights.  I made it big enough to hold the ESP32, a barrel connector and 3 Wago wire connectors. ... I printed it in PLA...

This cube box was specifically designed for the ESP32-EVB board. I intentionally left the buttons unattached from the top object, making it easy to add them separately as needed. My main intention behind creating this model was to control my AC using...

Remix of LayneBernardo ESP32 case design, increasing the spacing for ESP32 board with pins and added screw brackets.

Based on the original curved case by 'pcky' i have added a socket on the back cover and two different ball socket mounts. One for standing on a table/desk the other for mounting to a wall. There is also a variation with a hole in the back cover which...

Remix adding slot for SD, external antenna, hole camera and Gopro mount

... to be done or reuse etc. The ESP32 case stays very tight to the base due to all the connecting pins. ... I have done it where I had Female Pin header sockets on the ESP and also the more common pins on it with the Female header on the mount side.

Most ESP32 camera cases I've printed from Thingiverse were too small for my WiFi enabled ESP32 camera module with an SD card, so I designed this case to accommodate my needs. The dimensions are perfect with a little wiggle room in the back where the...

# EN I wanted to design a ESP32-Cam case with tripod as a week-end project. The tripod is single part printed. I print with .8mm nozzle and .3mm layer height 3x M4 nuts + 1x M4L20 screw required OnShape Link :...

Case Enclosure for ESP32 Camera This compact case provides a secure fit for your ESP32 camera module. The durable plastic construction protects the camera from accidental bumps and scratches, ensuring it remains fully functional at all times. A...

Screwless ESP32 enclosure, featuring a straightforward lid design. Included is an .f3d file for those who wish to modify and personalize the case. ...Additionally, I've provided a .stl file of the board itself, kindly verify that it corresponds with...

This is a case for the ESP32 cam. (see i.e. https://www.fambach.net/esp32-cam-modul/) It consists of three parts: 1) The main part, where the PCB can be pressed in 2) The bridge, where the camera is seated on 3) The lid, with a hole in the middle...

Housing for ESP32 and DHT22 humidity sensor and temperature sensor.

I made this design to use it with ESP32-CAM and a MicroUSB board to plug it.To have the thinnest case possible, I cut the PINs that are too long.ESP32-Cam on Aliexpress hereMicroUSB Board hereTutorial to configure it with tasmota firmware here (In...

Now the plantygon can accommodate an ESP32 that can be fixed with 4 M3 screws. An LCD screen 128x64 and a DHT22 sensor find their place on the side hexagonal panels. Side panels are designed to be jointed without any tool or screw. ...DHT22 was fixed...

I have built an ESP32 radio (https://github.com/Edzelf/ESP32-Radio) on a 70x50mm perfboard. The following key-components were used: Speakers https://www.aliexpress.com/item/4000127737256.html?spm=a2g0s.9042311.0.0.22f54c4devAQBT MP3 decoder VS1053B...

I have built an ESP32 radio (https://github.com/Edzelf/ESP32-Radio) on a 70x50mm perfboard. The following key-components were used: Speakers https://www.aliexpress.com/item/4000127737256.html?spm=a2g0s.9042311.0.0.22f54c4devAQBT MP3 decoder VS1053B...