esp32 devkit 3d models

Completely customizable case for ESP32 devkit v1.

ESP32 DevKit case ESP-WROOM-32 30 pin

ESP32 DevKit C Board Case Fits For AZ-Delivery CP2102 development Kit Buttons built into the top allowing user to press on-board buttons without removing the cover

This is a remix of ESP32 DevKit V1 Case (Thick). ...The only difference is that both parts now lay flat on the bed rather than 1cm in the air for the top.

This is ESP32 devkit v1 case. Please leave comments if you want me to improve. If you found this useful, please donate what you think it is worth to my paypal.me. Help cover the time of design. ... Thanks, Enjoy!

Case has cutouts for USB, LEDs and pins will stick out of back of case. If you want a version of this case where the pins are fully shelled/enclosed - see: https://www.prusaprinters.org/prints/50035-esp32-devkit-v1-chunky-case Print instructionsFront...

Attention!! ...This case for a narrow board with a non-standard width of 25.5mm I strongly advise you not to buy such a fee. But if you have already purchased it, here is the case for you. ESP32 DevKit case

This is a small enclosure for a ESP32 DevKit board (available at aliexpress). It has openings for USB and a few small cables. I created this for my CNC mill as a websocket controlled illumination (from within bCNC) (WS2812 LED ring) for my router.

Remix of BKGoodman's ESP32 DevKit Case with the following modifications: 1. Extended case bottom to cover and protect ESP32 pins (female Arduino jumper wires fit perfectly in the slot) 1. Slightly taller base to allow top to close properly 2. More...

I made a case for esp32 wroom devkit. It has a small window at the back for the wifi antenna (better connection).Also the pins fit into the case.10% Infill - Grid. ...You could even try with less since its just a case.Print the lid upside down - no...

This is a compact housing unit designed specifically for the ESP32 DevKit board, which can be purchased on Aliexpress at...

A simple case for the DOIT ESP32 DEVKIT V1

Case for the ESP32 devkit module (38 pin). I have the one from AzDelivery which fits perfectly. Not 100% sure if all the boards fit. You can click the board in place on the 4 small standoffs. This case provides access to all the pin headers and an...

Attention!! ...This case for a narrow board with a non-standard width of 25.5mm I strongly advise you not to buy such a fee. But if you have already purchased it, here is the case for you. ESP32 DevKit case v2

This is newer version of my ESP32 DevKit V1 case, suitable for 3D printing. It has an exposed USB port and a snap-on lid with ventilation, LED cutout for viewing onboard LEDs, and two buttons built-in which less you depress the on-board ESP32 buttons...

This is case is used to take an ESP32 DevKit-V1 which can run off battery power - i.e. no wires. So - I wanted a cheap and easy way to battery power my ESP32. But - A normal AA battery is rated to about 50mA, and only runs maximally at 1.5v. So even...

I previously mentioned compatibility with NodeMCU boards, but that was an error - the design actually caters to DevKit boards. The case has been successfully printed using both Dimension (ABS) and PRUSA MK3S (PLA) printers. The design is publicly...

Device Kit mit ESP32 WROOM32.

A simple case to house the ESP32s I got from amazon **BOM** *None of these links are affiliate* - ESP32 - https://www.amazon.ca/dp/B0B3MY3P9T - Antenna - https://www.amazon.ca/dp/B07X5XD4NR **Features** - USB slot for programming after installed -...

I looked for a case for my ESP32 project but none of the ones on Thingiverse really appealed to me. So I took bits and pieces that I liked from them and made my own. I included the openSCAD files in case you want to modify it to suit yourself. Note...

To address this need, I created an ESP32 enclosure that securely houses the clone development board. In addition, I added markings to make it easy to identify the pinout of the ESP32's pins. ... My hope is that others will find this design useful as...

Simple case for a DOIT ESP32 DevKit V1 36pins devboard. ...Top press fits on bottom part.

A case for the ESP32 devkit with the possibility to install an antenna. ...Both buttons of the devkit are accessible.

Remix case for the 34 pin version of the DoIt ESP32 DEVKIT V1 board. Fit is pretty tight on the pins but it will work. ... This is a remix from https://www.thingiverse.com/thing:4125952

I extended the front panel of the NodeMCU mount designed by 2dom to accommodate the DOIT ESP32 DevKit V1. To ensure compatibility, I repositioned and resized the screw holes and slot openings accordingly. Since the spring clips were unnecessary in my...

This is a case for the ESP32 DevKit C V2 by AZDelivery. It has a hole for the MicroUSB connector, individual pin sockets and a zone without the lid groove to have a better grip on the ESP32 for removal. It's still a work in progress, so it...

ESP32 DevKit case ESP-WROOM-32 30 pin What changed 24.12.2021 minor fix increased thickness of the bottom of the main body added stoppers above the board What changed. A hole was added for the light from the LED Openings were created for better...

Criei um case para acomodar a placa ESP32 devkit C e utilizá-la como adaptador de controles sem fio (via Bluetooth) nos consoles Playstation 1 e 2.O modelamento foi feito levando em consideração as tolerâncias para impressão 3D, não sendo necessários...

This is a Snap-Fit Case for the latest ESP32 Devkit v4, which has (compared to the Devkit v1) a smaller PCB without screwholes and where the antenna is sticking out. As far as i can tell, there are no other cases for the the Devkit v4, which i why i...

Designed for 16*2 LCD with I2C-adapter and ESP32 DevKit V4 from AZ Delivery Connection cable standard RJ45 network cable. Either with PoE or use the 8 wires individually LCD + ESP32 housing can be printed without supports (only in the hex-nut...