esp32 housing 3d models

Mind setting the right class when you compile it using ESP-IDF, also doing a idf.py menuconfig And adjust display configuration to match the connected ESP32 SPI Gpios. Keep in mind that it's always safer to use the HSPI pins:...

(SINGLE AND DUALCOLOR VERISON IN THE FILES) I used these threded inserts: https://www.aliexpress.com/item/1005005083203380.html?spm=a2g0o.order_list.order_list_main.98.1d821802gb8ysK I used this IR LED camera ring:...

The holes in the bottom part of the box should be tapped for those screws.Cam usageThis ESP32-CAM is designed to be integrated with HomeAssistant. ...More info about firmware and software can be found at <a...

Homekit32 - ESP32 Case - DIY Smarthome Control ============================================= I'd like to introduce you to my small DIY Smarthome project. In this project, I only wanted to control some of my plug sockets using Siri or through the iOS...

In my application, there is an opto-isolator input circuit on a small piece of stripboard, to isolate the track voltage from the internals of the device - this circuit is accommodated in a separate partition of the box to the ESP32, and the output...

Simple case for this ESP32 board with an OLED display. Includes front window for OLED, detents for buttons, and knockouts for USB, battery and all pins. ...Case snaps together nicely requiring no tools, screws or fasteners to open and close.</p>...

small case for the amazing ST7789 1.3 ips tft (bare) display and esp8266 or esp32 board with usb, like the d1 mini. place for a phone battery, power switch, 3 tactile switches, external j pole antenna, the unit is fully portable. the antenna is tuned...

Like this one https://www.ebay.com/itm/2pcs-TTGO-LORA32-868-915Mhz-ESP32-OLED-0-96-Inch-Blue-Display-Bluetooth-Antenna/152777264372?epid=24011353807&hash=item23923c0cf4:g:1kAAAOSwMFFbrLy- I used these on/off switches...

However, it's already meeting my needs and I believe additional modifications could further safeguard the ESP32 cam against moisture. I spent approximately two hours printing both the tap and body at high quality settings. To minimize support...

The Geekcreit ESP32 Development Board is a powerhouse of innovation, boasting a robust WiFi and Bluetooth connection that opens up endless possibilities for creators. This cutting-edge board is built on the ultra-efficient ESP-32 chip, which delivers...

These are the electronics parts I used for my cameras: USB Breakout ESP32-Cam There are quite a few different versions floating around, so if they differ it might not fit this case. **UPDATE 2019-06-23**: With the orientation provided by the top and...

A generously sized enclosure specifically designed to accommodate a wroom32 ESP32 dev board and a compact 1.8 inch TFT display, boasting an impressive resolution of 128x160 pixels. The box is spacious enough to permit the straightforward connection...

This is an external WIFI ESP32-Wroom-32U board with a AM312 sensor as the HC sensor had too much false positives. Maybe the AM312 has less or the wifi is seperated enough where I haven't had any to date.. The Board chip is snug on the interior...

A simple wall mount (and cover) for ESP32-MB. I have modified the Case design from Cybernetic's beautiful one (improved cam stability and enlarged case), whose I thanks. For the wall mount I used and modified a project found here on Thingiverse,...

Thanks mojocorp for the great case design.&nbsp;I added a GoPro type mounting as described in https://www.thingiverse.com/thing:4072374 and I extend the case to fit for a ESP32 CAM with an attached programming shield (ESP-CAM-MB). The shields usb is...

You can get the power directly from a USB connection on the printer itself.Requirements:2 Self tapping screws of 3mm2 M4 nuts and bolts (16mm length)1 ESP32-CAM (https://www.aliexpress.com/item/1005003804757059.html)1 Micro-USB breakout board...

A customized enclosure for the Heltec ESP32 LoRa with golpins already soldered in place can be found at http://s.click.aliexpress.com/e/bewzo9UG. This particular case features a modified design that does not include internal PCB brackets. As a...

I recently bought the Makerfabs ESP32-S3 parallel TFT board. It sits flat on the desk and I thought it would be better to have it held up at a 45 degree angle. I have a bunch of M2 screws and nuts, so I designed a simple frame around them. It takes...

(ESP32-3248S035C)Display and case on one level.For example:https://de.aliexpress.com/item/1005005928255980.html?spm=a2g0o.order_list.order_list_main.11.4a535c5fYamG2U&gatewayAdapt=glo2deuFits the following 60°...

## Components | Description | Store link | |----------------------------|-------------------------------| | M5CoreInk |[M5Stack](https://m5stack.com/collections/m5-core/products/m5stack-esp32-core-ink-development-kit1-54-elnk-display) | | M5Stack...

A case for the ESP32 Cam board that has no lid, the board snaps in with little force. It has 3 mounting points, with 2 holes each. There is a version for M1.5 (1.75mm) and one for M3(3.25mm). The holes are 14mm apart. This desing was made to be able...

I have designed a small, handy case for the WEMOS ESP32 D1 Mini version. Board just snaps in place (start with the USB-port when inserting) You need 4 M3x6 screws to fix the lid. There are two versions of the lid: Version 1 for directly...

... part. Over time this will result in a fully customizable and modifiable PFD to suit your specific needs. For a list of parts and textual explanations head on over to my website: https://www.bitsanddroids.com/custom-esp32-lcd-pfd-for-mfs2020-part-1/

ESP32 DevKit case ESP-WROOM-32 30 pin What changed 24.12.2021 minor fix increased thickness of the bottom of the main body added stoppers above the board What changed. A hole was added for the light from the LED Openings were created for better...

Waveshare screen link: https://smile.amazon.com/gp/product/B07P6MJPTD/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1 This uses M2 screws that came with the screen (or you can use any that you have), and M2 threaded inserts that are heat-set from...

Zudem habe ich die LED am Sensor ausgelötet.In WLED dann unter Config - LED Preferences - Button 0 GPIO der 32er Pin und Pushbutton ausgewählen.Anschließend Speichern.Sind alle Rest-Einstellungen erledigt, kann man das Licht durch kurzes Antippen...

Criei um case para acomodar a placa ESP32 devkit C e utilizá-la como adaptador de controles sem fio (via Bluetooth) nos consoles Playstation 1 e 2.O modelamento foi feito levando em consideração as tolerâncias para impressão 3D, não sendo necessários...

Esta va entre la parte delantera y la plancha, usar pegamento y guias de filamento, un poco largas para una vez soldados los cables sirvan para encajar con la parte trasera La alimentacion del servo de la cabeza va puenteada dentro de esta con la...

This bracket is for mounting an ESP32-Cam microcontroller in a bird nesting box. There are fixtures for 5mm LEDs. I use infrared LEDs, so the camera can be used in the dark without visible light. However, this requires a small modification of the...

Additional components include plywood (80mm x 250mm), base chip board (80mm x 160mm), two rods (5mm Dia x 250mm), one threaded spindle and nut, one ESP32-CAM, Neo Pixel Ring (16LED), an old USB cable, and a 5V power bank. The assembly is pretty...