esp32 lora 3d models

The "ESP32 LoRa" is one of these Micro Controller Units, combined on a printed circuit board with an OLED display, and a LoRa (long-range) transmitter/receiver. Imagine a little thermometer in your greenhouse - the display on it shows the current...

ESP32 LoRA Communicator (work in progress) Based on a $10 ESP32 LoRA board from AliExpress. https://bit.ly/2GYMoE0 These boards are documented here: https://github.com/osresearch/esp32-ttgo In the attached files, there are two case designs: a square...

A Case for Heltec ESP32 LoRa

This is a case for a dev board with ESP32, a LoRa chip and an OLED made by Heltec, the board might not work the most well built, but it's handy for experimenting. The board often comes with a small coil antenna with a IPEX connector so I made space...

This is a project for a development board with ESP32, a LoRa chip and an OLED made by Heltec. The board's design might not be the most polished, but it's incredibly handy for experimenting. The board often comes with a compact coil antenna featuring...

This is a case for a dev board with ESP32, a LoRa chip and an OLED made by Heltec, the board might not work the most well built, but it's handy for experimenting. ...The board often comes with a small coil antenna with a IPEX connector so I made space...

ESP32 WiFi + Bluetooth + OLED Display + Lora

A customized enclosure for the Heltec ESP32 LoRa with golpins already soldered in place can be found at http://s.click.aliexpress.com/e/bewzo9UG. This particular case features a modified design that does not include internal PCB brackets. As a...

Added some pads inside the case so that the Heltec board can sit on top of the pads instead of relying on the battery or the switch

You can find this same product on their website at...

Like this one https://www.ebay.com/itm/2pcs-TTGO-LORA32-868-915Mhz-ESP32-OLED-0-96-Inch-Blue-Display-Bluetooth-Antenna/152777264372?epid=24011353807&hash=item23923c0cf4:g:1kAAAOSwMFFbrLy- I used these on/off switches...

Case for TTGO ESP 32 Lora with OLED Display. ... I purchased these on/off switches...

SG ------------------------------------------------------------------------------------------------------------------------ Battery Mod for my Heltec ESP32 LoRa Wifi Case * heltec housing: https://www.thingiverse.com/thing:3769481 * I use my ESP32...

This is a case for the version 2 of the TTGO ESP32 LoRa development board with external antenna. Inside, you can fit a small LiPo battery. From the case, you have access to the Reset button, power on/off and the SD Card slot. You will need three...

Shopping list: * board: https://www.ebay.com/itm/SX1276-ESP32-LoRa-868MHz-915MHz-0-96-Inch-Blue-OLED-Display-Bluetooth-WIFI-Kit/383042074826?hash=item592f1638ca:g:Zd4AAOSwArNdJdsd * push buttons:...

https://www.youtube.com/watch?v=n6k_8D885sE This is a case for the version 2 of the TTGO ESP32 LoRa development board with external antena. Inside you can fit a small LiPo battery. From the case you have access to the Reset button, power on/of and...

This is a remix to fit with Heltec V3 (USB-C), with external antenna, more space for a battery, slider power switch, no screws needed and thin wallsOnShape Link:...

I'm using an ESP32 module from Heltec that combines Wi-Fi and LoRa capabilities, along with a built-in antenna for wireless communication.

Case for a TTGO ESP32-OLED board created for G6JME This is based on a design by Yogatech - Thingiverse thing https://www.thingiverse.com/thing:3443245 Designed to not require screws and so so no screw posts or bosses within the case. Antenna socket...

This board contains an ESP32 chip, SX1276 LoRa chip, Wifi, BT and even a Neo-6M GPS receiver. I Added a 0.96in OLED display on it, and been looking for a compact casing, that would let me open and close it regularly to change the 18650 battery...

Tight and precise model, you'll likely require some extra refinement to reach optimal quality. ...Vertical gaps must be filled to ensure proper printing, then carefully trimmed out for a flawless finish.

Printed with supports on the 'bottom' part 4 pin JST- ZH connector compatible https://www.ebay.co.uk/itm/283986512811 Thanks to another user uploading an STL for a case, I reused their very clever buttons ...

American Human: 3-gram lightweight enclosure for iNAV radar from Oliviver C, available online at a popular RC forum https://www.rcgroups.com/forums/showthread.php?4189550-iNav-Radar-Lightweight-Version/page20#post41902809

For TTGO T-Beam V1.1 ESP32 LORA with GPS NEO-M8N Case Using Button Head Allen Key M3 x 8mm bolts for Case and Allen Key M2 x 5mm bolts for PCB (need 4 of each Bolts) the PLA or PETG will grab on to the thread of the bolts to secure the pcb and case...

Hardware used: - LILYGO TTGO ESP32 LoRa v1.0 board (can be possibly modified for other models) - Short shaft rotary encoder (15mm plum handle) - Two panel mount push buttons (one is for the selection, the other is to replace the internal button)...

This is a case is made to hold a "LILYGO TTGO ESP32 LORA OLED v1.0" developer module alongside with a rotary encoder. A case also provides place for a 18650 battery, a power switch and a buzzer. One handed operation is possible. The idea behind...

Docking station for 3x ESP32 "MySondy Decoder Housing - V4 Improved" Fits exactly for the (4797115) https://www.thingiverse.com/thing:4797115 I had a better result with printing in draft mode. When you like this model please don't forget to like...

This is a case for the TTGO version 2.1 ESP32 LoRa development board with external antenna, designed specifically for the ESP32-Paxcounter project on GitHub. The case provides full access to all connectors and the reset button, ensuring seamless...

Hello, this is an updated rendition of the original text. Four precisely calculated screws are required, each measuring 2.2 millimeters by 6 millimeters in diameter. ... Updated as of December 2nd, 2019.