ev800d 3d models

Bracket to hold magnifying lenses in Eachine EV800D goggles. I used 3m VHB tape to attach it, but any double stick tape or glue should work. I searched for 'magnifier lens replacement' on amazon for the lenses. ...

Simple eyeglass holder for Everyine EV800D.

Small improvements on the spacer for fpv goggles EV800 et EV800D, the ring on the top improve to pass easily the band and remove the ring on the bottom

Glue the screen adapter to the bottom of the printed EV800D case and then it can slide into the printed tripod adapter for this tripod...

This is a housing for converting the Eachine EV800D box goggles to a stand alone monitor. To simplify the assembly, the screen and the buttons are held in place with a bit of hot glue or a flexible adhesive (E6000 or similar). Put a bit of...

This is a 67mm extension I made so I can see the screen on the EV800D clone googles I just got. The tabs are separate to increase the strength. The profile is pretty good, but it needs a good height raft to prevent minor deformation on the female...

This housing serves as a protective case for the internal components of the Eachine EV800D FPV freestyle drone or racing goggles. With this setup, you can remove the screen and mainboard and place them in this casing, effectively turning it into a...

This is first spacer for EV800D tested in real life. They fit good and prints well. There are no wird "build in supports", in slicer there is only needed support under the clips. ...

This is first spacer for EV800D tested in real life. They fit good and prints well. ... There are no wird "build in supports", in slicer there is only needed support under the clips.

Just a part to convert your ugliest hat into a fpv goggle device!!Surprisingly comfortable compared to the original straps and easy to lock and unlock your goggles. Material:3 x   M3x10 bolts1 x    M3x25 bolt for the lock knob (optional)3 or 4 mm...

Simple benchtop holder for the EV800D monitor. Contoured to conform to the curvature and angles of the back of the screen. ... Easily rest the monitor on your workbench or share with friends while you fly.

Magnifier lens adapter for the Eachine EV800D FPV goggles. Allows mounting 107x50x4mm welder lens. Mounting: Glue or screw the adapter to the googles. Cut the lens to fit you nose. ...Trim the top corners of the lens to fit inside the goggles.

Small Clip to use the lens inside any Eachine EV800D Fpv style Goggles ,lens from...

After snapping the clips open on the first attempt, I reattached them with extra care, noticing that they were slightly thinner than the standard clips used on the EV800D model. ...To ensure a snug fit, I carefully bent each clip at a slight angle to...

I created a custom spacer for my Eachine EV800D FPV goggles to fine-tune the focus by simply sliding the screen further back from the lens, which was previously causing a slight blur that made my eyes strain. ...This precision-made spacer measures...

External 3800mah 2S Gens ace lithium battery mount for EV800D goggle system. Double or triple your battery life! Works like Fatshark Goggles now and one less charger to drag around! The stock battery is 2 cell and has no balance tab, causing short...

I'll make a custom cover for the ev800d and ev800 mask by attaching it to the side. This way, the module will protrude as little as possible. First, I need to cut out a square to accommodate the module. Be careful not to mess up this step. Since I...

I modified the design of https://www.thingiverse.com/thing:2262741 (Thank you villamany) to fit the glasses more accurately. I decided to break down the spacer into three pieces - BackSide, FrontSide, and hooks. This way, only a small part in the...

Mod version to power up with a lipo, bec 5v si required: https://s.click.aliexpress.com/e/_DmbOh4f

Really liked the case so I designed a screen shade that mounts to it, I was lazy and didnt put in a concaved area for the front two screw heads so youll have to remove them but it hasnt affected the rigidity of the case in my experience if you use...

This is an adapter for the mounting of an Eachine PRO58RX receiver unit to Eachine EV800 oder EV800D FPV-googles. You can alos mount other RX units with this mount. Production: Can be printed on FDM, SLA and DLP printers. ... Needed parts for assembly:...

For the love of box style goggles, I have EV800D for years and now the digital era has come yet it refuses to surrender. ...Lets give some touch of digital technology by mounting an LCD monitor with HDMI input so I can use it with HD video receiver like...

External Battery Mount for EV800D Goggle System Boosts Battery Life by Double or Triple Your Original Capacity. Say Goodbye to Constant Recharging with This Essential Upgrade. Now, Your Fatshark Goggles Work Like Never Before, and You'll Only Need...

This is adapter to mount additional lens from model EV800DM to EV800DYou have to buy:Eachine Ev800dm Goggles - Zoom Screen MannifierYou have to print 2 pices of adapterPrint wih 0% fill and brim 3-5mm without supportNext open goggle and you have to...

<p>I'm using the bad shipped with the goggles to store them in a bigger bag.</p> <p>The only issue with it is that it could turn the power on by pressing the button for long enough, due to another item being in the same storage.</p> <p>I made this...

just a longer version of the 30mm ,, this ir 65 mm

I primarily employ this affordable goggles for troubleshooting purposes. However, finding an optimal viewing position can be challenging when trying to place them on a desktop surface. ...This stand effectively resolves that issue while also enabling...

I'm using the basic pouch provided with the goggles to keep them in a larger bag. The only problem with it is that it could accidentally turn on the power by holding down the button for too long, because another item was touching the storage...

Case for VRX Eachine 58proTX modeled by myself is designed to a bit loose fit because you need to add a bit of glue from a hot glue gun (i did it like that) on that side where are connectors, to hold both parts in place. ...Or you can leave it like that...