external spool holder for flashforge dreamer 3d models

I used them to adapt other brands' filaments to my Flashforge Dreamer NX 3d printer. The part is only the one that has to be mounted on the printer. Other parts for adapting the various internal diameters of the other filaments must be made. ... The two...

This upgraded rendition of a fellow user's filament holder boasts several enhancements.

To overcome this problem, I switched back to using the rear holder for a while, but eventually, I decided that a side mount solution was the better option for my setup. So, I set out to create my own version of the idea. The first iteration stayed...

This is a precise replica of the Flashforge Dreamer 3D printing device.

I'm searching for a dual fan duct for my Dreamer printer and I found inspiration in this [Blower/ Turbo Flashforge Creator Pro Part Cooling Duct remix](https://www.thingiverse.com/thing:2826878) design. ...This is an excellent solution, but it won't fit...

Here is my first design of a Flashforge Dreamer side panel with a cut-out at the bottom so you can mount your spool holder with the panel on. I know that it looks like I've just chopped it off, but I agree with you - it saves a bit on filament...

I altered the radius and clamping system.\nIf twisted filament rolls are getting you down, take a look at my rotating filament stand models.\nhttps://www.thingiverse.com/thing:2237807\nhttps://www.thingiverse.com/thing:2252123\nPrint...

... that are 11mm thick, including the heated bed. Be aware that these clips can get close to your nozzles, so lay out your models carefully! Print Settings Printer: flashforge dreamer Rafts: No Supports: No Resolution: 0.2 Infill: 15 Notes: print 4!

... **Print Settings** * **Printer:** Flashforge Dreamer * **Rafts:** Not required * **Supports:** Not necessary * **Resolution:** Set at 200 for optimal results * **Infill:** Use a density of 10-20% for balanced performance **Important Notes:**

This Figure printed on Flashforge Dreamer with Wanhao Black ABS required no Support, but I added some anyway. I grabbed this one from makeprintable and removed the logo from the base. (https://makeprintable.com/printables) Print Settings: Printer:...

Anti-Jamming Feeder for FlashForge Dreamer. If You're Using an Older Version, Adapt the Concept Based on This Original Model: https://www.thingiverse.com/thing:431115. Since I Specifically Designed It for My Left Extruder and Rely Solely on My Right...

Using BaronWilliams' Side Panel Fan Mount for Flashforge Dreamer (www.thingiverse.com/thing:667612) as a starting point, I modified it and then attempted to replicate the original's slotted design. Although my recreation is not a perfect match for...

... ... The filament guide bracket on my Flashforge Dreamer broke so the folks over there were kind enough to send me the files to be able to print my own. So, just in case anyone else runs into this problem I thought I should share it with Thingiverse.

This is the second Version of my Toolbox for Flashforge Dreamer and Dremel Idea. It´s mounted in the sidepanel - for files, scalpel, tweezers and calliper. V4 20mm wide V5 25mm wide If you are tired of twisted filament rolls :) take a look at my...

This is a filament holder I made for our printers. ...It can be used for Dreamer and Creator Pro (not suitable for Creator Pro 2016) You can attached this filament holder at the side of the printer. ... For Dreamer please remove the vent plate.

When working with PLA on your Flashforge Dreamer/Inventor, it's often helpful to have a simple latch to keep the front door securely open, especially since PLA requires adequate cooling during the printing process. ... The front door has a tendency to...

This is the second version of my Toolbox, designed specifically for Flashforge Dreamer and Dremel Idea machines. It's neatly mounted in the side panel, providing easy access to essential tools such as files, a scalpel, tweezers, and a caliper. The...

This clip is designed specifically to secure the rear cable within the Flashforge Dreamer, holding it firmly in place inside the device. Due to its design, this particular clip can only fit snugly into the bottom screw holes for the cable. ...In fact,...

This is a model of the Flashforge Dreamer 3D printer. ...Print Settings Printer Brand: LulzBot Printer: TAZ 5 Supports: Doesn't Matter Notes: rotate model 90 degrees on the X axis to minimize supports Category: 3D Printers

The X Axis Carriage For Dreamer 3D Printers Offers Enhanced Reliability and Strength Replacing The Standard X-Axis Carriage On FlashForge Dreamer Units, This Custom Design Ensures Continuous Functionality Even In Extreme Printing Conditions. Note...

Printer: Flashforge Dreamer Rafts: Any Supports: Yes Resolution: .2mm Infill: 100% Notes: Minimal supports on this, two small spots where screws sink into the grill face. Recommended to use these; can't hurt anything and the screws hide ugliness. Be...

__Things__ - [External Filament Mod - Flashforge Adventurer 3](https://www.thingiverse.com/thing:3626515) - [Locking bowden connector](https://www.thingiverse.com/thing:4269840) - [1kg spool holder for monoprice...

Exposing bare spots along the entire length of the Z-axis rods in the Flashforge Dreamer 3D printer is a common issue. These holes can be found from one end of the rod to the other, visible in images and observed by users. ...They are not isolated...

Ajout d'un port USB de chargement a la FlashForge Dreamer : Matériel nécessaire : - DC-DC 12V/24V a USB 5V 3A : https://www.amazon.fr/gp/product/B07H6KXGDW/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1 - Bouts de cable Voir les images pour le...

Installation It's helpful to have a 2.5 mm ballpoint allen wrench, similar to the one included with the Dreamer, since the screws are located in tight spaces and this type of wrench can be inserted at an angle for better access. Installation is...

This coupler is used to connect a piece of PTFE tube to the feeder, and have it go through a hole in the filament hatch, in order to use external filament holders with the hatch closed.I use it with the 1kg spool holder for monoprice voxel by Ryoichi...

Cooling air duct specifically designed for the right extruder on the FlashForge Dreamer, along with other printers sharing a similar left side blower configuration in dual extrusion systems. The standard cooling system prioritizes airflow to the...

This is a camera clip designed specifically for the FlashForge Dreamer carriage. It may fit other models if their carriages share similar construction. To install the clip, simply insert the top and gently wiggle it downward. The bottom will...

Print Settings Printer: FlashForge Dreamer Rafts: No Supports: No Resolution: .30 Infill: N/A Notes: I find that small objects like this print best at "High Quality" (40mm/sec speed) with thick layers: 0.30mm for the first and all layers. How I...

Use thin sheet steel (0.2mm ~ 0.5mm) for the bottom of the removable bed and one of the Flashforge build stickers for the top. Attach the mag-clips to the bed using the 3mm bolt and nuts from the original Flashforge build plate with enclosed printed...