external spool holder for flashforge dreamer 3d models

This is a HEPA capable filter I designed for the Flashforge Dreamer. This will mount directly to the back using the original M3 bolt holes, and you can use the stock bolts if you want, however I recommend buying longer bolts to avoid the headache. ...

flashforge spool holder adapter for Gizmodorks PLA spool

Although I'm extremely pleased with my Flashforge Dreamer, a persistent problem has been the way the cable harness to the heated head drapes down onto the rubber belt in specific positions, which had me decide to design a swinging arm that would...

Print in petg or similar for higher heat resistance. Supports are required from the bed, and possibly internally, dependant on your printer/settings, but can easily be removed later. ... I couldn't find the part listed anywhere after a failed print...

The innovative Falshforge Dreamer 3D printer embodies cutting-edge technology and design.

Designed specifically for spools sourced from 3D-Factory in Yafo. ... Print Settings: Printer: FlashForge Creator Pro Rafts: None Supports: Not needed Resolution: 0.3 mm with three shell layers Infill: Twenty percent density Notes: This is my preferred...

... Allows filament to either feed externally from behind or internally up through the back hole. Simply slide into place from the front and fix with either pin or something like BrianHooker's cable harness guide--the white part seen in the photos.

By dimensions, it has to be printed in parts: 4 corners, 2 short union pieces for sides, and 1 rear union piece with 2 holes to insert fiber from an external roll. ...The front union added a support for the GoPro, this piece had to be printed with...

made specifically for spools I get from 3D-factory in yafo Print Settings Printer: flashforge creator pro Rafts: No Supports: No Resolution: 0.3 mm and 3 shells Infill: 20 Notes: that's how I printed it, works fine for me Category: 3D Printer...

I acquired a metal case for my PI 4 from Ali and wanted to keep it off the desk. Since I couldn't find a suitable solution, I created this simple mount to attach to the side panel. It's essential to use supports to ensure stability. ...The design is...

To avoid potential issues with printed components fitting properly or having gaps that make them not suitable for use, consider adjusting the print settings of back plate curved layer so it does fit flush instead of remaining slightly concave after...

Flashforge Adventure 3 1 kg spool holder

Flashforge Creator Pro2 Spool Holder Extension

This is a lid spacer with external spool holders designed to interface seamlessly with the Flashforge Inventor 3D printer. It may also be compatible with other printers, such as the Flashforge Dreamer and the Dremel Idea Builder. To complete this...

1x U-Scheibe M10 Large filament holder for 300mm spools. Also suitable for small ones. Shaft M10 threaded rod. Bearing in ball bearings to move the heavy spools with little force. Everybody should have this holder, because some spools are damaged at...

Official FlashForge Adventurer AD5M Spool holder, removed "LXD" logo.

New spool holder for old-type (wooden) Flashforge Creator. Fits standart 1kg filament spools. ...You should rotate holder model upside-down in your slicer.

Adapter for Flashforge Creator Pro 2 original spool holderThis adapter mounts to the original spool holder allowing you to use third party filament reels

Designed specifically to complement the Ender3 spool holder, this innovative accessory enables users to seamlessly integrate smaller spools like those from FlashForge. ...By incorporating a threaded design, it eliminates the need for supports, ensuring...

Da Vinci Jr External Spool Holder Freedom to Access Panel Without Interruption Design Version 4 Achieved

Our 1kg spools were too wide for the other Flashforge Creator Pro narrow hole spool holders, so this is a lengthened version, remixed from turbo2ltr, that works with spools that are 9cm wide. Category: 3D Printer Parts

Spool Holder for the Flashforge Creator Pro Fasteners - Bolts: 2 M8 x 75mm Fasteners - Nuts: 6 M8 Rollers - Bearings: 4, 8mm diameter, 22mm width, 7mm thickness

Improved Filament Spool Holder for Flashforge Guider II Printers. Printing Instructions: Print alone, without any added support structures. ...Optimize settings to achieve an infill density of 10-15%.

... Adventurer 3 Spool Holder Adaptor 3DNY. ... This is specifically designed for the latest iteration of the ADV3, featuring a reconfigured center of the spool holder that splits into four distinct sections rather than the three seen in its predecessor.

This is a Prusament spool holder / washer for a Flashforge Creator 3 printer I noticed there is a groove on the inner ring of the spool that jams as it unwinds this provides a smoother surface to roll on

This is a remix of DavedFX's universal spool holder for the Flashforge Creator Pro. ...I designed this to be completely smooth to allow the spool to turn freely.

This is an upgraded version of DavedFX's widely used universal spool holder specifically tailored for the Flashforge Creator Pro. ...Its design ensures a perfectly smooth rotation, allowing the spool to spin freely without any hindrance.

... modification I've developed for the original filament spool holder design. This external filament holder is designed to reduce vibrations caused by the filament spool on the top of the printer while optimizing the overall size of the setup.

The Coupler will help you run a short length of PTFE tube from inside the filament compartment through to the exterior and aloo you to print 3rd party filaments on large spools without having to leave the compartment door open. Add your 4mm diameter...

The result is this external filament spool holder designed specifically for 6204 bearings (14mm thick, 20mm inner diameter, 47mm outer diameter). You can find these bearings online or print them yourself. Alternatively, the axle can be mounted...