external spool holder for flashforge dreamer 3d models

and figured it would be a good starting point to design my own spool holder for the cassette. This was my first exercise, as I couldn't find anything online that fit my needs. Since the printer has two extruders, I designed a double setup. There are...

I switched some time ago away from the spool holders at the back of the printer, because they are high friction compared to having a spool holder that runs on skateboard bearings. That leaves these old spool holders hanging off the back of the...

---------------- [English] Adaptation of the mjoaris spool holder (initially for Ender 3) for installation on the Flashforge Creator Pro 2 (2020). The mjoaris's original project is at this address https://www.thingiverse.com/thing:3209211 If you...

This is a custom spool holder designed for the Flux 3D Delta printer. The printable parts require an additional set of 8 countersunk M5 x 12mm nuts and approximately 130 quarter-inch slingshot pellets to assemble correctly. Unfortunately, I...

This is a spool holder adapter for the adventurer 3 (old model). ... It works with the door closed.

This is a holder for iPhone (including case) for use as Continuity Camera on an external screen. The holder could be configured in Fusion 360. ...The STL file is for screens with 22mm thickness, iPhones with 11mm thickness and a tilt of 15% downward.

Spool Adapter for Flashforge Adventure 3 SeriesThis design is a spool adapter for Flashforge Adventure 3. It can be attached to the existing holder to mount regular spools of filament. The connector, with four tapering slots, has a diameter of...

Holder for External Hard Drive is mounted behind the TV, specifically designed for Philips TVs but can also work with other models assuming hole spacing remains standard. I used the same fixings to hang my screen on a wall, so it's likely compatible....

This Dial Indicator holder, designed for FlashForge Creator rails, features a central 8mm hole and two 6mm x 6mm magnet-holding holes. ...Simple to print and install.

... appears to be more responsive if you use a a tablet pen. ...I designed a pen holder based on this spool holder design: https://www.thingiverse.com/thing:6286294. Alibre Atom was used to create this design. ... Printed at 0.2 mm layer height 15% infill.

I would like to have a holder to keep safe my external hard disk when I use it on may laptop, and I didn't find one so I design it. It easy to customize to adapt for different harddisk size or different laptop screen It is more easy to print base and...

Plastic - ABS Temperature - 245/105 Speed 60/30 mm/s Nozzle 0,8 мм Layer 0,2 мм Infill 100% Supports 30% Adhesive - PVP+ALcohol https://enterodez.ru/

Here are some key features of the Wanhao filament holder for FlashForge Guider: - **Sturdy Construction:** The holder's robust build is designed to withstand normal wear and tear, ensuring it stays securely attached to your 3D printer. - **Easy...

I need this holder for second printer in IKEA Lack enclosure, so I edited it. Intead of 4 holder supports, now its just two. ...It will work with any double side tape.

This holder is specifically designed for external mosfets measuring 52 x 42mm, as depicted in the accompanying images. Its dimensions align perfectly with the outer measurements of the mosfet itself, which are 63 x 50mm, leaving no unnecessary space...

Please note that you will need to replace your factory spool holders to use this Pi4 case since it replaces one of the factory spool holders on the rear of the FFCP. I used tmessori's design to allow easier access to change the filament and free up...

... makes it a breeze to assemble everything with some glue. Check out another project I've got on Thingiverse if you're interested - a Laptop Phone Holder that's also a must-have for anyone who wants to stay organized while working from their laptop.

A hands-on upgrade for the Longer LK4 Pro and comparable printers featuring identical spool mounts.

Viel Spaß beim Drucken :) Dankeschön an den User Shintak für´s Erstellen des PTFE-Adapters :) ----- Spool holder for large rolls for the Flashforge Adventurer 3 (NEW VERSION!!). On the old one, the inner stub does not fit, because the printer's...

This is for use with external spool holders. I recommend: https://www.thingiverse.com/thing:1471454 Print two of these and sandwich a 608 bearing between. Insert it in the hex hole at the top of the Z axis. Just slide filament through the angled...

I've designed and remixed this from the following: Filament Spool Holder https://www.thingiverse.com/thing:3363933 4-Part Door Cover https://www.thingiverse.com/thing:3329107 I used the 4-Part door as a template to save measuring it all, and I'm...

Here are the rewritten texts: Filament holder with a FlashForge Dreamer 3D printer.\nI designed this hook for 1 kg Nunus filament, which no longer fits inside the cabin.\nI used an existing prototype (http://www.thingiverse.com/thing:938750) as a...

This holder was designed specifically for external MOSFETs with hole dimensions of 52 x 42mm, as shown in the accompanying pictures. The dimensions fit snugly around the outer measurements of the MOSFET itself (63 x 50mm), leaving no extra space...

... arrived, I found a spool with a massive diameter hole inside. Therefore, I had to print a new spool holder immediately. ...Unfortunately, I couldn't find one online; so if you need one, this design works great and the filament is excellent too!

Print Settings: Printer Brand: FlashForge Printer: Finder Rafts: Doesn't Matter Supports: Yes Resolution: High Infill: 15% Notes: To assemble this camera holder, use M5 flat-head 12 mm screws and M5 nuts, or for a more permanent bond, apply supper...

Filament Extender for FlashForge Adventurer 3/3pro

PSU holder for MK3sThere was no optimal PSU holder for me, so I designed my own.The holder is screwed to the rear panel of my enclosure.I designed it in two parts to avoid disconnecting the cables from the printer.You need four M3 screws 8mm or 10mm...

PSU holder for MK3sThere was no optimal PSU holder for me, so I designed my own.The holder is screwed to the rear panel of my enclosure.I designed it in two parts to avoid disconnecting the cables from the printer.You need four M3 screws 8mm or 10mm...

FlashForge Creator Pro users can now breathe a sigh of relief as the innovative Bowden holder prevents the pesky tube from pressing against the extruder, thereby solving one of the most frustrating problems with extrusion that has plagued them for...