extruder filament 3d models
226117 3d models found related to extruder filament.thingiverse
Extruder filament guide for Anet A8 mk8 extruder Print Settings Supports: Yes Resolution: 0,2
thingiverse
This extruder filament guide is for the Anet printers when needing to print flexible filaments such as TPU, Ninjaflex, Filaflex, etc... The part prevents the flexible filament from escaping or deforming during the extrusion process and tangle inside...
thingiverse
Extruder filament guide remix to fit the metal version 12mm depth. ...
grabcad
Started project not finished in this evolution. Just an idea.But you can finish and upload the full project for all congregation in GRABCAD. ...Good luck.
thingiverse
A remix of an extruder filament guide with the screw holes recessed to allow the screws to go deeper and more threads make contact.
thingiverse
I started out using another Thingverse Ender 3 extruder filament guide that I downloaded here, https://www.thingiverse.com/thing:3010366. It worked fine, but it basically just pushed on, without any particular alignment capabilities, and did not...
youmagine
This is my version for the extruder filament driver for my QU-DB extruder (1.75mm filament), where I wanted to have more force applied to the filament. I guess this set will also work on MK7 extruder too, but may be there is room problems. I have...
thingiverse
Simple skrew replacement for Ultimaker extruder Instructions This is a replacement for the ultimaker extruder filament holder. Mine had the bad attidute to loosen during long time printing, so I replace it with another one with a lock nut. I test it...
thingiverse
I designed two extruder filament guides to solve this issue. One for stiff filament like PLA, ABS or PETG and one for flexible filament such as TPU. These guides guide the filament in the best way for inserting en while printing. The stiff filament...
thingiverse
filament guide to go with the dual extruder I used 1/4" nylon tube. ... https://www.thingiverse.com/thing:3559787 extruder beacket https://www.thingiverse.com/thing:3582112 dual extruder fan assembly
thingiverse
Extruder attachment guides the filament out the rear so it doesn't bunch up under the crossbeam
thingiverse
Threading the filament into the bowden tube of the sintron MK8 extruder (http://www.aliexpress.com/store/product/Sintron-1-75mm-3D-printer-Kossel-Mini-MK8-Extruder-for-E3D-Bowden-Delta-Rostock-Free/114769_32429475134.html) is quite troublesome. It...
thingiverse
Filament guide for Adimlab printer or other printer's that use the Mk8 extruder. This was not designed by me. ... I'm posting this here as a convenient place to download for others.
cults3d
I made an external filament guide to add to the top of a Greg's or other extruder for better guiding of the filament. I found that mine usually misses the guidler one and so I added this to the other side on top of the extruder housing. ...I like my...
thingiverse
Further more, when a filament change is needed, the Guide-Support and poly-guide-tubing "combination" simply slips up and off of the extruder tension arm providing easy access to the filament itself. This is a simple part to print. If you use a...
thingiverse
5 - Attach heat sink and fan onto the extruder body with two long screws on the filament exit side. 6 - For better thermal conductivity, apply some thermal grease between the extruder body, the cover plate, and the heat sink. Printing Tips: -...
thingiverse
But when loading filament to the extruder, I often find the filament gets as far as the fitting on the Bowden tube and gets caught on the face of the fitting. Cutting the filament to a taper does help some but, I needed more. So I designed this...
thingiverse
Simple filament guide for MK8 extruder, allowing easier filament change. You might need to insert 5mm long piece of bowden tube between the guide and the pneumatic fitting (as shown in the second photo). This will make the filament change even...
thingiverse
... lid is snap-fit. (M3) ***Not tested on a bowden system might get in the way with the leadscrew*** **This is a remix from 2 models** *Filament sensor* https://www.thingiverse.com/thing:4629979 *Extruder Arm* https://www.thingiverse.com/thing:3059247
thingiverse
It means that filament can simply bend, then clog and finally get shredded by the gear (it happened to me next day after mounting bulldog in my printer). This little upgrade guarantees that such situation will never happen again. ... Inspired by...
thingiverse
Many Bowden-type extruders have a pneumatic tube connector with a 10 mm thread - the tube is held rigidly in place, and the filament is driven by the motor - into the end ot the tube, where it stops. This item fits into the thread end, and funnels...
thingiverse
I made an external filament guide to add to the top of a Greg's or other extruder for better guiding of the filament. I found that mine usually misses the guidler one and so I added this to the other side on top of the extruder housing. I like my...
thingiverse
Filament guide for the MK8 extruder, nests into the Bowden fitting in the bottom and clears the idler bearing and hobbed gear. Second file is a simpler one that doesn't nest, and just inserts, if the first one doesn't fit. ...Print Settings Rafts: ...
thingiverse
This guide helps to insert filament into the boden tube when using the low cost extruders available from Amazon and Ebay. ... Such as this one: https://www.amazon.com/gp/product/B01JGNKVF0/ref=ppx_yo_dt_b_asin_title_o01__o00_s00?ie=UTF8&psc=1