fan duct for noctua nh d15 in combination w tall memory modules 3d models

Designed specifically for Noctua's 40mm fans, but may also fit other 40mm fans. 1mm thick. 6 versions available: * Short * Short with screw holes * Medium * Medium with screw holes * Long * Long with screw holes I designed medium and long skirted...

Required : - a Dremel to cut the square hole - a drill to make the four M4 holes - a soldering iron - x4 screws BHC or CHC M4x35 (Mesure the exact length and cut the end for a better finished before to screw the fan) - x4 scews BHC M4x6 I am not...

Consequently, when used on thin air ducts, they prove to be inefficient due to the tendency of air to recirculate through the gap between blades and fan duct. To address this issue, a small cover can effectively mitigate opposite airflow. Trying it...

This is a fan duct replacement for the Bear Extruder 0.7.0-beta MK2.5S MK3S https://www.thingiverse.com/thing:3716110 With blower fans (in this case the part cooling fan), the majority of the air flow goes to the left side (looking at the printer...

The item is a Fan Guard for Cyclops with a 25mm x 25mm Duct, along with M2.6 screws in sets of six. A 25mm x 25mm x 7mm fan is shown being used in the photo. Print Settings Printer: idbox! ... Rafts: No Supports: Yes Notes: Cura supports Overhang 60°...

This is a duct for a vertically-mounted 50mm squirrel-cage blower fan. It snaps directly onto the blower. I'm using it for my modified 3DR Simple 3D printer, but it is pretty generic and could be used for just about anything that needs such a part.

Remixed from SuperNatto's "Ender 3 Pro PSU 92x25mm fan mount" Added a bit of height to properly fit a Noctua NF-A9 Fan with rubber mounts because it was pressing against some components of the PSU

We print it upside down, but need to support the holes which we screw in the M3 screws. Prusa Orange PETG was used for the Fan Housing and Case Top. Generic black PLA was used for the Case Bottom (from eBay, I think). This was my first ever PETG...

Its for The Ortur Obsidian Fan Duct origenal stl Data what in the sd card includetet. Es ist für Ortur Obsidian das Lüfterkanal steck Dings was in der SD Carte dabei war. ...(Original STL) Print Settings Printer: Ortur Obsidian Rafts: Doesn't Matter...

When I was designing this fan duct, z axis adhesion is my concerned, I don't want too much air flow for the filament. So, I distribute 2/3 of the air to the heat sink, and 1/3 to the filament. Anyway, the air flow for filament is way bigger than I...

fan duct what more could i say ? ...for a old socket 7 cpu fan

My e3d clone came in slightly under the original designers' specs, so I whipped up a makeshift fan duct on the fly. ...It's nothing fancy, but it should get the trick done.

The edges of my prints were warping and curling out of control, so I swiftly designed a duct for the larger 60mm fan that lay idle nearby... and it worked like magic. For optimal print settings, consult your own expertise, as results will vary...

Fan Duct For Sigma3D (Arcanus66) Sigma3D: http://www.thingiverse.com/thing:817504 Print Settings Rafts: Completely Irrelevant Supports: Doesn't Matter At All Resolution: A Precise 0.2 Infill: Solid, Every Single Time

Duct fan for the power supply that came with the Anet A8. Fan is 90x90 square, and also a 100x100 square connects with the PSU. The distance between fan and PSU is exactly 50mm. ... Print Settings Printer: Anet A8 Rafts: ...

Noctua fan (40x40x10) adapter to "trianglelab DDE Direct Drive Extruder upgrade kit for Creality3D Ender-3/CR-10 series 3D printer"

I have crafted a customized fan duct for the Anet A6, which snugly fits around the heating nozzle. Pros: -Fan air is blown directly onto the nozzle area. Cons: -Printout visibility is significantly reduced due to the duct's design. Two versions...

For connecting the LM2596 to the Noctua fan, you can simply use the cables that Noctua delivers with the fan. Just cut of one side from the Y-split cable, solder it to the LM2596 and connect it to the fan. You only need the black (out - ) and...

Shortened version of snap-in 5015 fan duct to fit with E3D V6 or clone (if used without spacer). Also improved airflow and printability of the part by adding some corners. Can be printed with no support (some overhang failure but came out good...

I used to have this cooling duct on my i3 which inspired me to design my own magnetic delta effector with a built in print cooling fan. I also wanted to put a capacitive probe on it, which it ended up in a pretty awkward position right in front of...

As the title clearly states, it is a case specifically designed for the Raspberry Pi 3B+, meant to house a Noctua NF A4x20 5V Fan. Recently, I set up OctoPrint on a Raspberry Pi 3B+ and wanted to print a case that would also allow fan cooling. I...

... and wear over time. However, note that before we proceed, three of the screw holes in the fan will need to be drilled, utilizing a size M3 drill bit, specifically for accommodating more common fasteners that match existing setup preferences.

I designed a custom shim to perfectly fit a Noctua fan on my Prusa I3 MK3 printer. The shim allows the fan cover to sit securely and flatly on the fan itself. ... To create the fan cover, I utilized this innovative design found on Thingiverse:...

... Engineering Computer-1 case. ...The case is designed to install only one case fan but I wanted to install 2 fans - intake and exhaust, so I came up with a fan mount idea to install Noctua NF-A4x20 as an extra fan. ... Form 2 | Grey Pro v1 | 0.1mm

... supports. ...Secure with two thermoplastic 3x14 screws. For easy mounting, enlarge the fan fixation holes using a 3mm or better yet, a 3.2mm drill bit. ...Print settings: Printer: SmartCub3D Rafts: No Supports: No Resolution: 300 microns (normal mode)

Introducing Fan Duct V3, designed specifically for PLA and featuring a J-Head cooling port. The latest upload includes a longer duct and downward-directed outflow ports to prevent excessive extruder cooling. Pair it with the Ulti-Flat X Carriage...

This is an adapter to attach a 120mm noctua fan to 1/2 inch (half inch) Loc-Line component. I used a vise to press them together and they fit really well and quite sturdy. You could use small screws and/or glue to keep them together, but I didn't...

Check out Colin's great source file for the fan finger guard. ...Print with the base down (will need to flip).</p>

Required : a Dremel to cut the square hole a drill to make the four M4 holes a soldering iron x4 screws BHC or CHC M4x30 (Mesure the exact length and cut the end for a better finished before to screw the fan) x4 scews BHC M4x6 I am not...

I revised the rear panel to enable the use of a 40mm Noctua fan. Additionally, I updated the files for both the case and front to allow the micro USB to be plugged into the screen instead of the Pi, which is the recommended setup. At this point, I...