fan duct for noctua nh d15 in combination w tall memory modules 3d models

MY FAN DUCT

cooling fan duct

This is a custom Octagonal bezel designed specifically for a 140mm Noctua fan, with the potential to fit other fans in its class. A 138mm diameter locating ring is strategically positioned on the back side, providing a secure seal around the edge of...

A 40x40mm fan is required for the 3D printer's duct. ...This specific fan size ensures proper airflow and cooling within the printer.

This is an FAN duct for the anet A8/AM8

Solid, functional, fan duct for Anet A8, with strong fixing.

... an inconsistent air distribution that prevents nice overhangs from being printed. To address this issue, I designed a modified fan duct that fits both the fan box and extrusion fans like the Sunon MF50151V1-A99 12V model with dimensions of 51x51x15.

I reworked my old 3D printer Flyingbear P902 on X-bot kinematics on rails and installed a high-quality Titan Aero extruder, which I actually purchased from Trianglelab in China, and what it lacks in authenticity makes up for in performance. To start...

The 40mm fan is designed for cooling the hot end's middle section, with a thickness of 1mm. ...Make sure to remove the brim prior to usage. This is my inaugural attempt at 3D modeling using Solidworks, and I have successfully created a sturdy holder!

This is a remix of the "Mean Well LRS-350 PSU Lids for 92mm Noctua Slim Fan" (https://www.thingiverse.com/thing:3197058) with the following changes: * fits a 92x92x25mm Noctua fan * 1.2mm wider lid to work with newer models of the LRS-350 psu (the...

this is a dual 5015 fan duct for the e3d hemera, the screws that are not blocked by the hemera are affixed by m3 bolts with nuts. the bolts that are covered by the hemera are m2 bolts with nuts, the head of the screw buts againsed the hemera, not...

I modified the Micro-Swiss Hot End fan duct for the Fang to allow for more airflow through the fins and improved cooling, so I cut a vent into each side of the heat sink to prevent it from blocking airflow entirely. There are two versions available...

I noticed that the Micro-Swiss Hot End version of the fan duct blocks the sides of the heat sink almost entirely, so I opened a vent in the side to allow more airflow through the fins and better cooling. There are two versions available - one is the...

Remix Satsana for Ender 3 V2 with fan for filament 40x40x20 and fan for hotend 40x40x10

After that, I routed the cable through a (3D-printed) PCI cover plate to the outside and connected the fan from the fan duct. In the BIOS I set the fan trigger to motherboard. That way, the air in the shelf will be sucked out if the motherboard...

The Zaxe Z1+ 3D printer comes with an exhaust fan that is designed to eliminate the harmful gas produced while printing ABS material. However, since I only use PLA material, the fan runs unnecessarily. To enhance the quality of my prints, I removed...

Print Settings Printer: NFire 1 Supports: No Resolution: .2 Infill: Shouldn't Matter Notes: There are three files: complete fan duct: nFire 1 50mmx15mm Squirrel Cage Fan Duct v1.2 or two easily (hopefully) printable pieces: nFire 1 50mmx15mm...

Designed specifically for the "MK9" extruder that comes standard with the Folger Tech Prusa i3. Prints successfully without the need for supports. EDIT: Initially, I was going to remove this duct since my other one works even better. ...However, I'll...

This is a modified version of http://www.thingiverse.com/thing:72912, as the duct in the original design was too low for my RepRapPro Mono Mendel, sitting about 5mm below the hot end's tip. ...However, this adjusted design works perfectly for me.

I attached a replica volcano heatbreak to my Hypercube Evolution and struggled to locate a compatible fan adapter. ...Since I'm running the stock mount, I improvised by lengthening the existing fan duct to perfectly align with the nozzle's outlet.

The fan on my Delta printer was misaligned from cooling around the hotend, prompting me to create this fan duct to rectify the issue. ... v1.1 sits roughly 0.5 mm higher and is a tad shorter, ensuring it won't collide with prints, particularly during...

A makeshift fan duct was created to enhance print quality while constructing a new extruder and carriage; your feedback is welcome. Made using 123D, it lacks an OpenSCAD file. ...The design accommodates a 60mm CPU fan (from an old computer), featuring...

This is a duct for the l9a, that allows you to add 2 * 40x40x20mm fans This screws directly on the l9a, using two of the 25mm screws. Printing: Rotate the model 180 degrees along the x or y axis. ... License: GNU GPLv3

This is a fan duct designed specifically for the Flyingbear P905 model. It incorporates a robust 40mm x 40mm fan, providing efficient airflow. The duct's adjustable height feature allows users to customize its position according to their needs.

This mount pairs a 2mm spacer with the adjustable bracket to secure the fan duct onto an E3D Titan extruder . The duct is based on Neo_Usagi's innovative design, modified to fit on the left-hand side. It still needs some refinement but works well so...

Clip-on front shroud to improve airflow and static pressure for noctua 1040 and 2040 fans. The clips are a work in progress and might not work reliably. I'm using the previous version with only two clips (that weren't sufficient), but I didn't want...

This is a fan funnel for a Noctua 80mm fan which I place in my ikea sideboard which I'm using as cabinet for my Monoprice Select Mini V2. Additionally only a hole is needed inside your cabinet with the proper diameter. This fan funnel can be printed...

This duct is specifically designed to work with the particular type of Bowden mount found at https://www.thingiverse.com/thing:2077676. The goal was to create a device that would generate a moderate-sized whirlwind, capable of blowing away small...