filament connector 3d models
230445 3d models found related to filament connector.cults3d
Video instruction manual of a similar type : https://www.youtube.com/watch?v=Xihc_VHMVi0 Material: 1 nut M5 (diam 8) 2 screws 3 X 12 .1.75 filament connector All you have to do is put a piece of PTFE on the nut side. Once the 2 filaments are...
thingiverse
... for the last peaces on your filament spool. Just conduct both peaces of filament on each side, put some oil on the inside to separate the filament from the connector-parts, warm it up with a lighter and press both sides together. Have fun! ...
cults3d
Use this small connector to join filaments when you swop them that so filament in the PTFE tube can till be retracted and pushed along.. ...Print in vase mode for good results.
thingiverse
Use this small connector to join filaments when you swop them that so filament in the PTFE tube can till be retracted and pushed along.. ...Print in vase mode for good results.
cults3d
This is a collection of connectors for using 1.75mm filament as pipes, tubes, wires, antennae, etc. for your model or prop build. ... Check out my other greeblies here: https://www.thingiverse.com/ajh1138/collections/ajs-greeblies
thingiverse
This is a collection of connectors for using 1.75mm filament as pipes, tubes, wires, antennae, etc. for your model or prop build. ... Check out my other greeblies here: https://www.thingiverse.com/ajh1138/collections/ajs-greeblies
thingiverse
Filament Sensor Halter mit Anschluss für Pneumatikkupplung zur Filamentversorgung
thingiverse
I have designed an alternative which should meet the following points: - No further materials are required for assembly - Anyone who has a printer can make the connector - Only a lighter is needed for heating - The connector must be able to be...
thingiverse
Generally other connectors are short and do not channel the filament to connection with the PTFE tube connector. I developed this model with a 5.5mm thread diameter to help those who go through this type of problem. The model has a hexagonal hole...
thingiverse
To respool the filament, stick the transfer connector's part A through the two spools. Then put the B part on the A part like a lid. Thread the filament into the hole in the empty spool and slowly start turning the empty spool, keeping the filament...
sketchfab
Replacement Filament Tube Connector for your dual extruder GB3.
thingiverse
It just add another pneumatic connector PC4-M10 thread, so you have connector inside and outside. --------------- Este es un remix del Enclosure Bushing Filament realizado por Raptor2063 el 30 de enero de 2021. ... Simplemente agregue otra rosca de...
thingiverse
As usual, when I went to figure out how to get filament through the Sterilite 20qt box, I was unsatisfied with the current offerings. I wanted to keep it sweet and simple, using the threads of the M10 PTFE connector. The threads in the inside...
thingiverse
An easy solution to connect PET filament ends when you making it.
thingiverse
Top mounting for the 10-15$ welder from Aliexpress like shown here https://www.youtube.com/watch?v=a3FwzuUcFFI I made a version with the hexagon Tool holder, and one without. The tool is the same, like we got with our Ender, so there is not...
thingiverse
Filament filter with M6 threads for pressure connectors
thingiverse
Since I had the problem that the two brackets have always shifted against each other on smooth surfaces and thus the filament roll was no longer optimally guided. If you have problems or suggestions, I will gladly help. Thank you jstck for the...
prusaprinters
I never liked having to push/pull the PTFE tube in and out of the filament sensor so I made an adapter to make things a lot simpler when loading/unloading filament.I used a very short piece of PTFE tube, 9.44mm in length between the adapter and the...
thingiverse
... two IKEA Kallax shelves. ...You can put that connector on the backside and it will hold both that no gap can be seen between the shelves. It's low filament and fast to print. ...This will don't hold two kallax's, it will only remove the gap between!
thingiverse
Created to help with running my filament from my SUNLU filament dryer to my Direct Drive Ender 5 Pro. I was having issues with the filament breaking at the opening in the lid after sitting when I print finished, this has fixed my issue. Modeled to...
thingiverse
I divided it in 2 parts so is easy to print if one of them broke, also I scale the connector B in 1mm to fit perfectly with the connector A. ... I printed with standard settings in Cura for PETG in my E3Pro.
thingiverse
The standard CR10 / CR10S printable extruder comes without an internal thread for the pneumatic connector to screw to it, So modified and put in some threads to firmly hold the pneumatic connector to the part. ... Modified from an STL downloaded from...
thingiverse
easily replace the filament Bolt L M3 x 50mm, https://amzn.to/3lwv49c Cutter Blades Refill 9mm, https://amzn.to/3kCBUsE
thingiverse
... your loop. The connector is not load bearing in any way. June 1, 2020 Update: I added files with the filament type engraved on the side of the connector. ...This could be handy if you have multiple loops organized by different types of filament.
prusaprinters
Pull it tight and cut off the excess. Insert the knot into the slot on the connector and slide the cord tight to make your loop. The connector is not load bearing in any way. June 1, 2020 Update: I added files with the filament type engraved on the...
thingiverse
Nothing too much, just added a simple screw mount for a pneumatic fitting for the ptfe connector Version 2 is I found the case to be too tight for the runout sensor so made the walls slightly thinnner and it now fits like a glove