filament puller 3d models
177662 3d models found related to filament puller.thingiverse
filament puller with nema17 without planetary gear ,standard nema 17 mounting holes , the rest files from original design
thingiverse
Variable Speed Filament puller I've uploaded the pcb I've used. Uses an arduino pro mini 5v. 12v power supply 2a. ...potentiometer and a easy stepper driver.
thingiverse
I like this design because i dont need some stupid durathane rollers :) I bought the paint/inkt rollers :) Because I already bought the Nema17 planetary motor as suggested by lymann...
thingiverse
I made some modifications to the original. ... Revamped for a nema 17 motor. Added a thickness gauge that will measure diameter of the filament. ... All of this is still untested so let me know how it all works.
thingiverse
Simple filament puller from extruder. Stepper motor controllers is required to use this. Part 4_spacer is for fitting 6mm axle to 8mm ID bearings. No need if there are available more suitable wheels Parts you need: Nema23 stepper motor 2X 50mm...
thingiverse
This winder is a remake of the Lyman extruder filament puller (seehttp://www.thingiverse.com/thing:380987 ) . The original design is using a stepper motor, and this design a geared DC motor. This design is more compact, with the motor on the back.
thingiverse
The original screws are used for mounting the thread guide in the melter and for mounting the filament sensor. the bearing to be used for the pulley is a 4x13x6 mm groove bearing I attach link ...
cults3d
The original screws are used for mounting the thread guide in the melter and for mounting the filament sensor. the bearing to be used for the pulley is a 4x13x6 mm groove bearing I attach link ...
thingiverse
A 22mmOD, 7mmH, 8mmID bearing used to support the motor pulling the filament on the Petamentor/Petamentor 2 Materials: 22x8x7mm Bearing:https://www.amazon.com/dp/B07XD6PLV1 8MM Diameter Rod (Length:45-60mm, I used 45) M3 Screw and Nut(To hold Rod)...
thingiverse
M4 screws for the springs, 608 bearings x4, M8 rod for roller centers. Roller is M3 nut/screw. ...Bottom roller D35 H60 Top Idler D25 H60 NEMA17 motor.
thingiverse
I needed to make a puller for my [filament extruder project](https://medium.com/endless-filament). I tried wingmaster's [one](https://www.thingiverse.com/thing:677144) which is a nice and compact design but in the end I had one too many issues with...
thingiverse
This is an extra part for the Filament extruder puller ( http://www.thingiverse.com/thing:677144 ). Sometimes the filament is wandering to the side of the pully. This extra wire guide makes the entry smaller holding the filament in the middle. ...
thingiverse
This gear for the Filament extruder puller (see: https://www.thingiverse.com/thing:677144) is for using a MFA 919D series motor. ... The motor has to be screwed from the outside onto the surface (see photos).
cults3d
This is an alternative Idler design for the Filament extruder puller I simply used a few rubber washers pushed together for the main pulling wheel and needed a matching idler. It uses two 2.5mm diameter screws and nuts for fixing the idler on 8mm...
thingiverse
Sometime ago I made the "Spring Loaded Caliper by ianjohnson" and also the "Simple filament extruder puller by james_III" and I thought that It would be a good idea to hook these 2 together so that the measurement device and the puller were as close...
thingiverse
This is an alternative Idler design for the Filament extruder puller by wingmaster http://www.thingiverse.com/thing:677144 . I simply used a few rubber washers pushed together for the main pulling wheel and needed a matching idler. It uses two 2.5mm...
thingiverse
I have found different springs (from Würth https://eshop.wuerth.de/is-bin/INTERSHOP.enfinity/WFS/1401-B1-Site/en_US/-/EUR/ViewCatalog-Browse?CatalogCategoryRef=14013510010101%40WuerthGroup-Wuerth-1401&CatalogCategoryID=WEgKD92eIw0AAAFDk3Jcaz5u) and a...
cults3d
I have found different springs (from Würth https://eshop.wuerth.de/is-bin/INTERSHOP.enfinity/WFS/1401-B1-Site/en_US/-/EUR/ViewCatalog-Browse?CatalogCategoryRef=14013510010101%40WuerthGroup-Wuerth-1401&CatalogCategoryID=WEgKD92eIw0AAAFDk3Jcaz5u) and ...
thingiverse
I found a lot of switch pullers on Thingiverse don't work for me, so I designed a really good one that works super fast on my keyboard (Redragon K552). ... One note, you should clip each end down a tiny bit to provide better clearance for fitting it...