filament roller ender 3 3d models
920928 3d models found related to filament roller ender 3.thingiverse
Spool roller for the standard creality spool holder - I made this to make the pulling action less eccentric and therefore less stress on everything. ... External - 56mm Internal - 36mm length - 60mm
thingiverse
Filament spool holder for ender 3 v2, but I think it would work on other printers too. Note: I had the bolts, nuts, washers, and bearings lying around. The bearing I used were 'bad' (for their previous purpose in a table saw motor) but they are...
thingiverse
If you look at your first couple layers at the default orientation in your slicer preview you will notice that it doesn't actually print the whole first layer, it thinks a bunch of the bottom is a bridge printed on layer 2, 3 etc. By lowering the...
thingiverse
This is a pin for Holspeed's filament guide. Was unable to find a screw so I designed a pin that works just as well. Dimensions are on the smaller side to ensure fit. Height can be reduced as it is longer than needs to be. X and Y dimensions can be...
thingiverse
Remixted -- Creality (Ender 3) Creality (Ender 3) Filament holder 80mm spools by mjoaris Nov 11, 2018 This is a Dual Roller bearing Spool holder that will secure onto the original Ender-3 spool mount, Necessary for a Dual Extruder...
thingiverse
The roller is angled to better support filament spools mounted slightly to the rear such as the deault Ender 3 v2 top mounting arm or my (more compact) rear mounted spool (https://www.thingiverse.com/thing:5330574). The angled roller also keeps the...
thingiverse
At the cost of my sanity, I have another Ender 3 Max upgrade for you. This time I modified a filament guide to work with the Max. It fits right under the plate that holds everything and is held up with M3 screws. You only need one M3 Nut to hold it...
thingiverse
I designed in Tinkercad a Roller Guide for better Rolling the Filament Rolls from Geetech 2019. Its not finished actually but it should work better than the Stock holder. ... This is designed to fit the space so it does not shake the whole printer when...
thingiverse
Please use support when printing part 1,2,3. ... also use raft when using PETG filament for avoid elephant foot
thingiverse
This is a mixed design from Holspeed and theroar, I liked the Holspeed design and snap to printer section and theroar bearing section (snap pin and bearing holder). ... With this guide I am not using the upper filament guide and it is perfect.
myminifactory
Подшипник: 2 x 6201Z; Размер: 12-32-10; Максимальный размер: 47 мм;
thingiverse
Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...
thingiverse
Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...
thingiverse
I have a different plan in mind for my printer, but in case anyone else is running into this issue, I added a hood to the roller to hopefully keep the filament from coming off the roller on any feed back from retractions. ... Anyway, as always I hope...
thingiverse
This is a remix of https://www.thingiverse.com/thing:5330621 to be able to use this filter holder (https://www.thingiverse.com/thing:5062767), still need the other parts from the original one
thingiverse
Filament roller for Ender 3 / 3v2. ... To build you need: 1) print all 3 attached files 2) One 608 bearing (8mm x 22mm x 7mm) 3) M4 x 16mm bolt and nut Attachment contains SolidWorks files if you want to fix something
thingiverse
I made a filament roller for Ender 3. I used for bearings 624ZZ U groove bearings. On one side I used shorter M4 bolts that hold the bearings tightly. On the other side I used longer bolts, because the filament roll width's can be a little different....
thingiverse
Filament roller for Ender 3 near extruder. ...Require 688ZZ bearing and M4 x 20mm screw
thingiverse
Filament roller for Ender 3 with 688ZZ bearing size and M4 x 20mm screw
thingiverse
same filament guide thing with the roller wheel that accepts 8mm OD bearings
thingiverse
So I created this roller for my Ender 3's filament spool holder. I made it for my eSun PETG spools, and the fit is perfect. For wider spools like Hatchbox you can probably print 3 of the center spacers (yellow) and only one of the end spacers...
thingiverse
Upgrade your Ender 3 Spool holder so the motor doesn't have to work as hard. I just used some bearings I found lying around. You may need to secure the bearing by putting it face down on a hard surface and lightly hammering on the plastic to properly...
thingiverse
Filament roller for Ender 3 (and Pro) with a bearing. Print it in fine quality 0.12mm infill 20% Takes appox 2 hours. You need a bearing 1. SKF608 or similar. 1.Press the bearing into the round ring 2.Press the bearing on the round pin...
thingiverse
An extruder filament guide with a roller for even smoother filament feed. Designed for the Ender 3, easily plugs on to the extruder holder plate. Keeps the filament from grinding into the extruder plastic, smoothens feed and ensures a clearance from...
thingiverse
A very simple filament spool holder to fit on the stock Ender 3 roller/pipe. Slide on to stop the roll of filament swinging and catching as it unwinds. Print 2 (one for each side) Internal hole is 32mm diameter, roller sleeve/bearing is 53mm...
thingiverse
It might be compatible with the Ender 3 "Original" edition as well as the Ender-3v2, but I cannot test it since I only own the Ender 3 Pro. I printed it in PETG, but I have no doubt that any filament material would do for this roller. ... ...
prusaprinters
A very simple filament spool holder to fit on the stock Ender 3 roller/pipe. Slide on to stop the roll of filament swinging and catching as it unwinds. Print 2 (one for each side) Internal hole is 32mm diameter, roller sleeve/bearing is 53mm...