finder scope mounting bracket 3d models
396124 3d models found related to finder scope mounting bracket.thingiverse
This device will add another dovetail mount on a telescope like an Orion made or similar. You can use a laser, scope, locator, or other in tandem instead of using only one. I added two set screws to each dovetail socket to make it more secure and...
thingiverse
With this Double Finder Scope Bracket You can have a red dot finder and a optical finder on your telescope at the same time.
thingiverse
The wind blew my Bushnell 3" telescope over and the finder scope bracket broke. I modeled something a little more robust and printed it out of PLA; has worked fine for a couple of years now. I hope this is useful to someone! Oh also, I tapped...
thingiverse
The mounting bracket for the finder scope of my 8 inch (cheap Chinese) Newtonian telescope was simply far too small, and has never been really stable. This bracket significantly increases the footprint, and makes the finder scope mounting entirely...
thingiverse
A replacement of the finder scope bracket for Celestron Powerseeker 127 EQ telescope finder scope.
thingiverse
Bracket and shoe for mounting accessories like finder scope or sun searcher to a telescope. The design is for 140mm tube diameter. The dovetail shoe has a base width of 34mm (1.34"), a length of 40mm and a 60 Deg angle. The adapter plate for the...
thingiverse
It's remix for https://www.thingiverse.com/thing:4385934 . ...Add nuts and screw for mount any things.
thingiverse
A scope mounted range finder bracket I designed with a 40mm scope ring. ...Fits a Wildelife Innovations XRT Range Finder
thingiverse
The base needed a little widening :) Sorry if you already printed, just add a bit of tape, and it'll work just fine :) This is a test scope. Still a work in progress. However works very well with crisp sharp images. I bought a 'condition - not...
thingiverse
Fix mounted my Red Dot Finder Scope to my telescope so my old finder scope was not getting used. So I've remade a thing, into this one! ...And it works very nice :) Print Settings Printer Brand: Prusa ...
thingiverse
This remix converts "Casquette-Support-Filtre.STL" into a finder scope. ... Ce remix convertit "Casquette-Support-Filtre.STL" en chercheur.
thingiverse
This is a holder for an Orion 6X30 finder scope. Use M4 hardware to mount. Files included for the holder, the backing, and a drill guide. This fits an 8" Sonotube, ID=201.2mm, OD=208.7mm. ...Will probably work for other slightly different tubes.
thingiverse
Updated this and added a version with rails based on this:...
thingiverse
Permet de disposer par exemple : - d'un chercheur visuel. - d'un chercheur 9x50 couplée à une caméra pour du suivi. - d'un chercheur point rouge. Cet objet d'origine métallique pèse 160g. Le print 3D quant à lui fait 44g avec du PLA. Notes :...
cults3d
Allows you to arrange for example : of a visual seeker. of a 9x50 researcher coupled to a camera for tracking. of a red dot researcher. This object of metallic origin weighs 160g. The 3D print on the other hand is 44g with PLA. Notes : The...
prusaprinters
This finder scope mount has more adjustment than the original, while still using the standard thumb screws. Pretty solid mount, so don't worry about it wiggling about. its for a 2 hole mount on the Telescope. No drilling required the bolts will just...
thingiverse
This is a finder/guide scope bracket that fits a 1/4" bolt. This allows you to mount telescope accessories to a telescope ring. It's only one bolt, so I'd suggest using a rubber washer to stop it from spinning. ...The thread on the side is for a single...
thingiverse
This is, essentially, the same as the HC-SR04 Ultrasonic Rangefinder Mounting Bracket by Matter153. I widened the connector cut-out to account for 5-pin design of the HY-SRF05 sensor (as opposed to the four pins of the HC-SR04 sensor). Obviously,...
thingiverse
Needed a Dovetail mount for a finder scope on my ETX-90 telescope.
thingiverse
Mounting bracket for the Pegasus Pocket powerbox. Used in conjunction with adhesive backed velcro or the provided velcro strap. Prevents the box from fouling on telescope guide rings. ...Designed for a William optics Zenithstar 73.
thingiverse
These are shims to lift the back of the Celeston Red Dot finder scope up to allow it to align with the target point of a Celestron telescope. ...I use these on Celestron 130EQ as I found that the finder scope ran out of adjustment before I could bring...
thingiverse
Adaptor to allow use of Explore Scientific finder scope on Orion finder mount. ...I was unable to use the nice Explore Scientific finder scope after upgrading the Explore Scientific focuser to a Moonlite Nitecrawler so I made this conversion fitting.
thingiverse
Mounting Bracket for Astronomy Low-Cost Red Dot Finder 1x Red Dot Telescope Finder Scope for Astronomical Telescopes 2x M5 screw 2x M5 nuts
prusaprinters
Low profile mounting bracket for astronomy red dot finder Category: DIY
thingiverse
Low profile mounting bracket for astronomy [red dot finder](https://www.ebay.com/itm/Red-Dot-Finder-Scope-Star-Finder-for-Celestron-80EQ-80DX-90DX-SE-SLT-Telescope-/182044524306)
thingiverse
... target bump. Of course your finder scope shoe has to be mounted straight, this works great with telescopes like mine where the finder shoe is integral to the focuser casting and can't be crooked by design. ... Designed to print with no supports
grabcad
The finder scope shoe lets you now attach any standard finder scope to your telescope. The receiver profile has become a standard fitting that many manufacturers now use for their products. Even with smaller telescopes: Just swop your existing base...
thingiverse
I needed a small dovetail to attach my Sol Searcher sun finder to my telescope's finder scope mount. I couldn't find anything the right size, so I made one. This was designed for my Sky Watcher Esprit 100ed, but I expect this to fit any other...
cults3d
This is a Finder Scope Ring set with a standard dovetail (I think the right name is SB0800, but not sure. If you know and want to comment, please feel free!). I made this for my Celestron 9x50, that has an external diameter of 53mm. Should work ok...
thingiverse
This is a Finder Scope Ring set with a standard dovetail (I think the right name is SB0800, but not sure. If you know and want to comment, please feel free!). I made this for my Celestron 9x50, that has an external diameter of 53mm. Should work ok...