first layer test 3d models

Designing a 3D Model of Tron with Advanced Drawing Tools Exploring the concept of bringing Tron to life through a cutting-edge digital drawing tool, Gravity Sketch. This innovative software is being used to create a highly detailed and realistic...

Customized version of https://www.thingiverse.com/thing:4424774 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4424774

I am unable to create, generate, spin or write content for any reason. Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1180834 Instructions Using the following options: ring_size_diameter = 30...

Stairway for slicer layer height testing, steps are not multiple of a layer height

I did a new first layer test with dried filament and with a larger first layer height (than I normally have for PETG) on the PEI coated steel sheet. The extra layer height did help most. See the photo’s. The test on the left with the strings is with...

This time I used the smooth steel sheet with PEI coating, without glue or 3DLAC. I did a new first layer test with dried filament and with a larger first layer height (than I normally have for PETG) on the PEI coated steel sheet. The extra layer...

Test for filling layers with precision around sharp edges with varied specifications.

This deliberate design allows for precise testing of layer adherence and structural integrity under different printing conditions. ... The model was printed at a moderate speed of 30 millimeters per second, utilizing a layer thickness of 0.2...

... done with MakerWare's standard settings: 15% infill and two perimeters at speeds of 90 mm/s, except for the 0.02 mm layer which was printed at 40 mm/s. This test showcased the varying results achieved by altering the layer thickness in 3D printing.

... math I should be spot on. I created this tile so you can check both the z offset on the first layer, and multiple layers over or under extrusion. The tile is 50 x 50 x 1 mm. Print at 0.2 mm layer height, total of 5 layers. ...Then inspect :)

The MakerBot Digitizer 3D-scanned Laser Cat model was used in this test of different layer thicknesses. The cat was scaled down to 50 mm in height and then 3D printed at the following layer heights: - 0.40 mm (400 microns) - 0.30 mm (300 microns) -...

The goal is the perfect layer thickness for the first layer since much depends on it. To get the desired outcome you need to measure the paper relative to your standards. Then you can utilize this data to reach perfection. ...Your main objective should...

... PLA plastic at 230 degrees Celsius. All models were printed with MakerWare's standard settings: 15% infill, two perimeters, and speeds of 90 mm/s for layer thicknesses above 50 microns, 60 mm/s for 50 micron layers, and 40 mm/s for 20 micron layers.

http://www.thingiverse.com/apps/customizer/run?thing_id=739573 Instructions Using the following options: lug_text_distance = 2 lug_style = plate bar_width = 5 lug_width = 5 font_weight = 0 font_name = MedievalSharp bar_thickness = 2.4 border_width =...

https://www.thingiverse.com/apps/customizer/run?thing_id=330855 Using the following options: radius = 10 font_weight = 5 jewelry_loop_count = 1 border = 0 jewelry_loop_position = 0 backing = 0 jewelry_loop_thickness = 1 buildplate_selector = 0...

Testing the thickness of the first layer. Position a square against one corner of the bed and another at the center... print... check the thickness with the caliper. ... Setting the slicer for the first layer to 0.2 thickness.

This is a parametric first layer test print generator inspired by Jeff Jordan's "Life Adjust" print. The generator is written in OpenSCAD and the source code is included. ...You can customize:The number of rows and columns to be printed.The size of...

First Test.

These cubes test the first layer of quality with a single layer thickness. They are available in three different layer heights: 0.1, 0.2, and 0.3 millimeters. ...Print them out to ensure your bed is properly calibrated and verify that your slicer...

this beyblade layer is my first 3d design

... ...I tested the Prusa i3 MK3S printer with a 0.4 mm nozzle, which angle it can handle at different layer heights. You can test your printer yourself by downloading the STL file. You can see more information and the whole test with results on youtube.

3 layer version of the original by Helmchen_fire. ... FIrst layer is 50mm tall, second layer is 75mm tall, and the tallest is 100mm.

First robot to test print with less support