flash forge creator pro 3d models

That's a direct quote from the FlashForge Creator Pro 2016 manual, but I've found that this printer can handle printing PLA through the right extruder for excellent dual-strusion prints. All it needs is an upgraded fan duct. Take a look at the...

You can also buy similar threaded inserts from ebay but you will need to dremel one end to be conic as shown in the picture. Print Settings Printer: Flashforge Creator Pro Rafts: No Supports: No Resolution: 0.2mm Infill: 20% Notes: Material:...

Printing settings used for this project include: - Layer height: 0.2mm (first layer thickness set at 0.3mm) - Solid layers on top and bottom: both set at 4 - Infill percentage: 30% - No skirt or brim was applied Available files for download are: -...

Print Settings: Printer: FlashForge Creator Pro 2016 Rafts: No Supports: Yes Resolution: 0.2mm Infill: 15% Notes: While printing without supports is feasible, I strongly recommend utilizing them. If you have Simplify3D, navigate to the Customize...

This version has been modified to fit the older Creator and Creator Pro models (from 2015 and earlier) which use round holes for mounting the spool holders. This model also offsets the holders similarly to the model by ajwammock, such that there is...

This version has been modified to fit older Creator and Creator Pro models from 2015 and earlier, which use round holes for mounting the spool holders. The model also offsets the holders like the [model by...

What do you do if you want to flash a new firmware into an Arduino-based printer but it won't take, despite doing all the usual things like making sure you have the correct drivers installed, configuring your programming device and software...

... Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=895187 Instructions Using the following options: textSize = 13 border = 1 stickWidth = 8 signWidth = 80 signHeight = 30 textMsg = FLASH stickLength = 90 thickness = 3

A miniature Flash logo, measuring approximately five centimeters in diameter, is not only an adorable addition to any desk or table but also serves as a functional coaster. Alternatively, it can be treasured by fans as a collectible item. ...I also...

... needs. ...Featuring wireless TTL functionality and a guide number of 36, this flash unit delivers exceptional performance in any lighting condition. ...Plus, its compact size makes it easy to carry around while still offering top-of-the-line features.

... to make sure things are going smoothly. I plan to create some timelapses soon to test this feature and will post one of those after I create it. Print Settings: Printer: FlashForge Creator Pro Rafts: No Supports: No Resolution: .2 mm Infill: 20

A fan holder for both extruder fans of the Qidi/Creator Pro with Flexion dual extruder allows the fans to be mounted separately from the block and motors for easier assembly, disassembly, and maintenance. It was always a pain to have to thread those...

This design should work perfectly on Flashforge Creator Pro with an OLD Hatchbox spool that has an inner hub diameter of around 32mm or 1-1/4 inches. I made some slight tweaks to this version from the ones I printed for myself, making the end flange...

A week ago, I got my FlashForge Creator Pro 2016 and was blown away by its performance. However, some issues needed addressing. Firstly, it's really hard to fit filament spools from other brands in the included spool holders, but printing...

You can purchase the plate at: http://www.homedepot.com/p/AFINIA-Borosilicate-Glass-Printing-Surface-for-H800-AFINIA-H800-BORO-GLS/206653633 Print Settings Printer: Flashforge Creator Pro Rafts: Yes Supports: Yes Resolution: .200 Infill: 100% Notes:...

There are numerous spool holder designs available for the Flashforge Creator Pro, utilizing either a bolt or rod. I'm focusing on creating a new part that holds an 8mm bolt, specifically using a 120mm length bolt, as this is my preferred setup. ...

... the Pi and set up in the yaml.conf to low too. Basic code for this can be found in the comments. Printer Settings: Flashforge Creator Pro Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Infill: 55% Notes: An infill of ~30% should work fine too.

Print Settings Printer: FlashForge Creator Pro Rafts: Doesn't Matter Supports: No Resolution: .20mm Infill: 20% Notes: Sliced with Simplify3D Filament - ABS or PLA (ABS preferable for high temperature applications) Infill - 25% Solid layers - 3 top,...

This is a filament runout detector for the Creator Pro, I opted for this option instead of using phisical switches because I work with very flexible filaments like Ninjaflex that are very incovinient to try to push over a phisical switch. I'm...

Use this to test bed leveling of your Flashforge Creator Pro and verify flatness of the bed to detect bubbles after installing a PEI or BuildTak surface. Features: * Magnetic * Adjustable, easy to customize dimensions for precise printer tolerances....

A Reimagined Version of Chewbone's Flashforge Creator Pro Adjustable Glass Bed Bracket Enhancements to Corner Piece: The screw slot is now extended along the entire length of the corner, allowing for effortless removal and swapping of these...

I love my FlashForge Creator Pro all but for one thing... When it's printing, the extruders cast an annoying shadow from the angled RGB Led Board. This simple "pimp" offers an alternative mounting solution for the LED RGB Board which uses 2 of...

... Additionally, the box for the dial indicator can be modified to accommodate this design. Sincerely, fdk Print Settings: Printer: FlashForge Creator Pro Rafts: No Supports: No Resolution: 0.20 Infill: 0.20 Notes: Printed on its side without support.

I looked at the filament mount my *Flashforge Creator Pro* came with and thought: *What if it had ball bearings?* So I did a re-design and later added a guide to prevent filament jamming. For a more detailed description see the pictures and texts...

I successfully printed this design on my FlashForge Creator Pro 2016 without issues. To help others print without supports, I've added images showing the support guides and cuts where the model's nerve is observed. This can be a useful reference...

I purchased a FlashForge Creator Pro 2017 for my business and was frustrated by the difficult-to-reach rear spool holders that seemed cumbersome. Unable to find an acceptable alternative, I decided to design my own solution. These new spool holders...

I chose to remove the right extruder motor since the left one is closest to the cooling fan which helps with bridging. This motor blank serves as a stand in for the unused extruder in Replicator 2 clones (Flashforge Creator Pro, CTC, Qidi Tech...

... Z-homing at 50% speed (50mm/min) for accurate leveling. Moves rapidly to the front of the bed @ 9000mm/min! Fast blob (less than 1s!). Moves rapidly to start position @ 3000 mm/min. Go print faster! Print Settings: Printer: FlashForge Creator Pro

I'm combining my designs for the FlashForge Creator Pro / PowerSpec 3D Pro Printer and all associated clones under the FrankenForge name. This is my latest creation: a 608 Bering Spool Mount Replacement designed for the FFCP/PS3DP Printers with 30mm...

... points Line spacing = 2 points Slit width = 4 mm Text style = -80 degrees Letter spacing = 1 point Lines of text: Line 10: Line 9: Line 8: Line 7: Line 6: Line 5: Line 4: Line 3: Line 2: This is really cool. Line 1: Flashing bright.