flashforge adventurer 3 filament 3d models

Julien Thibeault's ingenious tube holder has been successfully merged with Gadittri's clever filament wiper to create a powerful hybrid tool that streamlines 3D printing operations.

... into the printer and fine-tuned a section of the filament guide. ...The issue was that my filament was causing my guiding tube to partially retract through the bracket, but now it can only go in for about half an inch before hitting a stopping point.

... creator printers out just to change the filament. ... So I designed this filament holder that fits on both of our creator Pro and Pro 2 printers. Depending on your print you may have to glue the 2 parts of the main body together. ... Printed in PLA+

I've been running my dreamer with filaments mounted overhead for a while, and I started noticing marks on the lid where the filament was dragging against it. The filament also wasn't flowing as smoothly as I wanted, so I decided to take action. I...

Upper slots allow filament to feed either externally from behind or internally up through the back hole; lower slots allow feeding from stock internal mounts, down through the rear hole, or from a side-mounted filament holder. Simply slide into...

Snap in filament guide tubes securely into place by aligning them with pre-existing screw holes on the frame. ...Replace M4 screws with new ones that are a bit longer for added stability.

I tweaked the file so the filament tube won't come crashing down anymore. ...Built a tiny shelf for the tube to safely rest on, securing it firmly in place.

To prevent the guide from sliding down when handling the filament or adjusting the guiding tubes, I've added limit stops at the top of the interface towards the back panel of the printer. The studs at the bottom can be used to attach threaded...

Next, I relocated the connection of the filament arm to underneath and added extra support to enable clip-together assembly. Additionally, I installed struts on the top arms to boost stability. ... Finally, I incorporated pins and holes so that...

Print Settings Printer Brand: PowerSpec Printer: PowerSpec 3D Pro Rafts: No Supports: No Resolution: 0.2mm Infill: 25% How I Designed This I designed the part using Autodesk Inventor software to create a precise and functional filament guide tube...

Just a simple bracket to bring the filament tubes outwards for easier use, and to prevent the filament from slipping off the spool and getting tangled between it and the machine. It also utilizes the stock filament tube holders for easy installation!...

I required a custom filament holder to secure the guide tube, as I already possess a reliable filament mount rack. After scouring various designs, most were either too compact or failed to snap onto my printer frame securely; perhaps this was due to...

Many spools are too bulky to fit on filament mounts - and once you've used up a significant amount of filament, having a massive spool takes up too much space. I needed a spool that was easy and quick to load and compactly stored (my Dreamer is on my...

... https://www.thingiverse.com/thing:2146587 Not many issues with the original I found. The fit is great for the lid, however, the angle of the guide with rough edges caused some hang with the filament. I added a tube for a smooth feed. ...

Pressfit spool holder extension for Filament Mate dryer box. Makes Spool spin much more freely. Has provision of the original Hygrometer. Can be printed support free. On purpose designed a little "too long" - when lid is mounted it will hold...

I modified the filament guide to suit my needs. The diameter of the securing rods was altered to 5.8mm due to difficulties with clicking them into place. ...I adjusted the distance from the rear of the printer to the center of the guide tubes to 35mm.

This is a remix of the object https://www.thingiverse.com/thing:1860297 modified and adapted to pass the filament from a reel hanging on the wall or under a shelf. ... It is used in conjunction with another printed item and found here on thingiverse.

This is a super simple spacer designed to fit between a Monoprice Voxel or Flashforge Adventurer on one side and a TUSH-style external spool holder on the other. The purpose of this spacer is to prevent the TUSH from sliding towards the printer.

Additionally, multiple small-diameter openings facilitate filament securement during non-print periods using simple sticking methods. I specifically used strong ABS material and painted a few layers of high-strength ABS for this project's creation....

The design incorporates a secure fastening system for the umbilical cord to the extruder head, ensuring proper alignment of 4mm OD PTFE filament guide tubes at a right angle to the print head. It also integrates cable management for fan wiring,...

... to be oversized with a lip on one side. ...This allows ProtoParadigm filament use inside your Dreamer printer. ...Instructions Printed in PLA material Infill level is 15% Layer height is set at 0.15mm It printed quickly and produced strong results

Printed a custom filament holder using various size spool/reel hole diameters, designed to replace the standard reel holders on my Flash Forge Maker pro printer. The new holder will fit perfectly in place of the original ones. ... Print Settings: ...

I replaced the faulty filament tube clips that often failed on the back of my Creator Pro with a more reliable system. The new setup mounts using the four screws that held the original clips in place. It's specifically designed to work seamlessly...

... clip. In contrast, the second device accepted it with precision without needing additional adjustments. The included shims elevate the lid, making room for the filament to be threaded through the narrow gap between the top and body of the printer.

If filament jumps the spool and wraps around the holder, preventing proper feeding and resulting in an extruder head moving wildly with nothing coming out, you'll be kicking yourself over missed opportunities. But with this effortless project, you...

The original feed pipe clip is too far away from my machine at times, so the filament starts to wind around itself on the spool and everything becomes jammed (most notably after my prints finish about 90% of the time). So I designed this as a...

... as a reference. ... This new version has a 22.5mm diameter hole to support a 3/4in dowel or standard bearings. The chamfer is only on the outside of the stands so that it prints clean and flush on the bed. ... Fusion360 and OBJ files are uploaded.

The gbzh01 remix didn't support the rod that I had available, so I recreated it from scratch using his as a reference.This new version has a 22.5mm diameter hole to support a 3/4in dowel or standard bearings.The chamfer is only on the outside of the...

Parts Needed: (optional) Drill or impact driver Specifications: Material: ABS Plastic Height: 11 inches Color: Translucent Thickness: 4 mm Width: 1 inch Diameter: 40 mm Volume: approximately 3000.2 cubic millimeters Weight: .3 kilograms Max weight...

This is the solidworks files for creating a wooden cabinet to store large and small makerbot filament, as well as flashforge filament. I have also included a PDF of the construction instructions for this project. MADE USING 3/4" PLYWOOD. Designed...