flashforge adventurer 3 filament 3d models

... holders for a straightforward setup! The device relies on a sponge to remove dust and debris from the filament just before it enters the guide tubes.\nBased on these:https://www.thingiverse.com/thing:153807http://www.thingiverse.com/thing:409297

I have a rack of filament spools mounted above my printer and after recently restoring my Tunell Filament Monitor to working function )one of the tensioner arms broke awhile back), I needed something to guide the filament to the rear input ports that...

I have a rack of filament spools mounted above my printer and after recently restoring my Tunell Filament Monitor to working function )one of the tensioner arms broke awhile back), I needed something to guide the filament to the rear input ports that...

Used a soldering iron to cut a notch in the filament door so a piece of PTFE tube can extend outside of printer and into a filament dryer. Prints fine with default Flashprint settings. Rotate model and use manual supports as shown. ... PC4-M10...

I'm excited to share with you my latest project - a modified Tunel Filament monitor designed specifically for the Tunel 3D printer filament monitor found here,...

Comes useful when you have both of your filament spools on the side, so the filament won't damage your printer's plastic edges. Desined to use with 7mm lid spacers: https://www.thingiverse.com/thing:1219953 Or without a lid at all. Should be...

I love the variety of filament alignment brackets available here for the Flash Forge Creator Pro, but one persistent problem I encountered was that after a few prints, the filament tubes would simply drop through the holes of the alignment bracket to...

I loved the original design but didn't want "Hatchbox Filament" to always stare at me from the back of my printer. The only thing I did was take off those words. ...Thanks for the great design!

Mount set readied for the Tunnel Filament monitor available here...http://www.toybuilderlabs.com/collections/best-selling/products/tunell-3d-printer-filament-monitor?variant=963597848 I refined several edges on the primary brackets and reinforced the...

Umbilical and filament guides are crucial for frame and print head, ensuring they stay vertical and providing a consistent feed. 4mm OD PTFE filament tubes can be included as part of the umbilical, particularly for the first half as shown in the...

By introducing strategically placed slots near the filament tube guide, they cleverly enabled easy removal when necessary. ...With just a simple pull of the tube guide from its hole and a quick slide out of the filament, the process became remarkably...

Recently, they started shipping spools with a larger diameter, so I designed a new filament holder to accommodate the change. After several iterations, I found this design works well with the new spools. To print it, I orient the logo face down, turn...

... wide spool. ...This revised design boasts an extended shaft, accommodating Hatchbox spools with ease. Furthermore, the machine's construction allows for additional clearance, preventing any filament guide tube from rubbing against its rear surface.

This is a derivation of http://www.thingiverse.com/thing:1339183 for the umbilical support, but with the filament support moved into the extruders. Assembly image shows brass bush in blue over cap head bolt. This is a 10mm length of 4mm OD tube...

... leading to a catastrophic failure. ...Undeterred, I opted for a more robust solution by substituting the flimsy legs with two sturdy 60mm M3 screws. To facilitate effortless insertion of filament, I cleverly added a subtle "horn-like" protrusion.

I wanted to plug the filament spool holder holes on my FFCP since I don't use them. They have been scaled up to fit appox 30mm holes from the 25mm models of the original designer. These were printed withHatchbox ABS. ...Hopefully someone else finds...

I wanted to plug the filament spool holder holes on my FFCP since I don't use them. They have been scaled up to fit appox 30mm holes from the 25mm models of the original designer. These were printed withHatchbox ABS. ...Hopefully someone else finds...

Next, slide the filament tube through the eyelets, which hold it in place by friction. I use a 1/4-inch OD polyethylene tube, but I believe a 6-millimeter OD tube would work just as well. ... Note that you must print this design in vertical orientation...

My first foray was making "hooks" that let me hang the holder from the top of my printer - it works surprisingly well, but when printing large pieces that take up most of the print plate, it can become a bit problematic due to the uncoiling...

I stumbled upon a remarkable filament holder on Thingiverse that caught my attention, but I wanted to give it a resizable twist based on the spool width. So, I designed one using three bridge parts to set the width of the holder. These bridges also...

I completely revamped the design inspired by TimmyTopHat's outstanding work on his remixes, but unfortunately, my print kept failing due to the arm falling off and the filament tube not sitting properly. To overcome these issues, I experimented with...

Human: Designed to fit the Flash Forge Creator Pro (2016) for use with current Verbatim PLA and ABS spools as of June 2016, these spool holders provide a secure and efficient way to manage your filament supply. For detailed specifications on spool...

Easier Heizbett setup with 3 point adjustment Print Settings Printer: CTC Dual Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.2mm Infill: 100% Notes: 2 Shells Print in ABS. Instructions 3.5mm hole front center between remaining holes...

First mount the base on the printer, after that you can slide the holder to the base. WORK IN PROGRESS, still need to make the testprint but should fit according to the drawings.

Converts the LCD mounting from an angled position to a fat position. This bracket replaces the LCD screen and the screen in turn mounts to this new mount. ... It simply changes the angle of the screen.

I took the source File and added a bore for the cold end, since it did not sit well in its original shape.

This is a reworked adaptation of Flashforge Adventurer 3 Spool Holder created by Stuart Waudby. ...A key alteration distinguishes it from the original design crafted by Stuart Waudby: the text emboss has been intentionally omitted from this rendition.

Z axis offset 3mm for CTC, Flashforge 3-D Printer, This is a 3mm offset for the CTC, flashforge printer for using a 3mm glass surface for printing

Print directly on one side without supports. ...SD card slots are rounded for effortless loading.

External spool holder for Flashforge Inventor II, Finder and Campustore Campusprint 3.0