flashforge camera 3d models

This becomes even more essential when printing ASA/ABS etc to cut down on the amount of fumes getting out.As the rear panel of the Guider II is metal the blanking pieces make use of 5.5mm square x 2.5mm high magnets.There will be another part to...

GoPro Mount for Flashforge Creator Pro. This mount attaches to the front of your printer, with a raised section in the middle to fit over the screw. Designed specifically for those who invested in the higher-end model, this mount takes advantage of...

... This holder is customizable for Flashforge Creator Pro filament guide tubes, keeping their ends at a safe distance from the printer case to prevent entanglement and positioning them at an angle that complements the superior Makerbot acrylic dome.

This customizable guide is specifically designed to secure Flashforge Creator Pro filament tubes. It elevates tube ends away from printer casing, preventing entanglements and optimally positioning them within the superior Makerbot acrylic dome found...

(see here a related thing: http://www.thingiverse.com/thing:1200876 ) This customizable add-on funnel improves the interface between the Flashforge extruder and the filament guide tubes, and helps keeping the guides in place, especially for the...

Adapter system for FlashForge Inventor This adapter system is designed to allow a FlashForge Inventor to handle reels from other manufacturers. Currently supported are: * FlashForge original 600g reels (180mm diameter) * eSun 1kg reels (200mm...

... **Print Settings** * **Printer:** Flashforge Dreamer * **Rafts:** Not required * **Supports:** Not necessary * **Resolution:** Set at 200 for optimal results * **Infill:** Use a density of 10-20% for balanced performance **Important Notes:**

The spool holders that come with the FlashForge Creator Pro (2016 version) are very limited in the dimensions of spools that it can hold. Most of my spools are either too wide or the hub is too small to fit on the manufacturer's holders. So I made a...

Printer Settings: * Printer: FlashForge Creator Pro * Rafts: No * Supports: No * Resolution: 0.3 * Infill: 25 Post-Printing Assembly: Insert the Inside Clamp.stl from within the printer, ensuring it aligns flush with the back of the device. Next,...

I designed this platform to support a camera phone, upright, capturing footage of my printer at work. This device was created using Tinkercad's user-friendly tools. ...You can modify it online by visiting https://www.tinkercad.com/things/hWJdD9UzGq2

Made the camera mount hinge wider on both ends to keep the C270 better aligned horizontally. My first make of the original mount (by ShaunDarkLord) had my cam tilting to the sides. ...This mod fixes that (for me, at least).

This attachment attaches securely to one of the two front pillars of the machine, allowing the camera to capture a clear and stable overhead shot of the printing operation.

Print Settings: Printer: FlashForge Creator Pro Rafts: No Supports: Yes Resolution: 0.20 or less Infill: 25% - 100% Notes: When printing the hanger and knurled knob, add a G-code command to pause the print just before covering the captive nut hole...

I've been struggling with printing larger objects on my Flashforge Adventurer 3, experiencing uneven adherence in certain areas. To resolve this issue, I designed an adapter that fits seamlessly into the print head, mirroring the hot end's design. By...

Print Settings Printer: FlashForge Dreamer Rafts: No Supports: No Resolution: .30 Infill: N/A Notes: I find that small objects like this print best at "High Quality" (40mm/sec speed) with thick layers: 0.30mm for the first and all layers. How I...

Cooling air duct specifically designed for the right extruder on the FlashForge Dreamer, along with other printers sharing a similar left side blower configuration in dual extrusion systems. The standard cooling system prioritizes airflow to the...

My spin on the FlashForge Dreamer Z-axis shim. This setup is secured with stability in mind, utilizing two existing M3-0.5 x 8 mm socket head screws that are bolted down for maximum support. You may need a shim if you upgrade your build plate's...

FlashForge printers come with a heated bed (good!) and a scarper tool (good!) made of metal (good!) that is electrically conductive (...) as are the EXPOSED BARE SOLDER contacts (not good) of the 24V bed heater. If the metal tool happens to touch...

The spool holders that come with the FlashForge Creator Pro (2016 version) are very limited in the dimensions of spools that it can hold. Most of my spools are either too wide or the hub is too small to fit on the manufacturer's holders. So I made a...

I wanted to use this fan duct on my Qidi printer which is a FlashForge Creator clone that's also a Markbot Replicator Dual clone. To do this, I needed super long M4 screws but unfortunately, I didn't have any and wasn't willing to wait three weeks...

So I had to purchase the only lid FlashForge provides for the 2016 creator pro, which is the unibody lid. If you're not aware, this lid is 12mm too short to sit properly on top and there are no brackets to secure it in place. As a result, here's my...

... clearance. Not a groundbreaking design, I know, but it does work and looks kinda nice. I went for a nice blue to match the Flashforge text on the build plate - lol! ...I left the protective blue sheet on to better photograph the sheet in place.

Here's a quick rundown on the customizations I added to my Flashforge. Check out the attached pic for a better look. To make the filament filter box shape work effectively, you'll want to print two pieces and place two sponges inside - that way, the...

(b) The standard spoolers are a perfect fit for FlashForge spools, but can't hold in place wider spool hub holes from other brands, like Hatchbox's. This design is longer and can accommodate most other spool brands. Might not fit all Creator Pro...

New V2 file added to hold glass plates firmly in place with improved design.\nThe Flashforge Creator and Dreamer corner posts now provide enhanced support for glass plates that are 9" x 6" and 5mm thick (and thicker). This redesign boasts tighter...

... i have clearance. Not a ground breaking design i know but it does work and looks kinda nice. I went for a nice blue to match the Flashforge text on the build plate lol. ...I left the protective blue sheet on to better photograph the sheet in place.

Here's a link to that little handle: http://www.thingiverse.com/thing:1241895 My Print Settings Printer - I used the Flashforge Creator Pro, a great printer. Rafts - I didn't need any rafts for this thing. Supports - My printer could handle some...

The spool holders provided with the FlashForge Creator Pro (2016 version) have very limited dimensions, unable to accommodate most of my spools. Either they're too wide or their hubs are too small to fit on the manufacturer's holders. As a result, I...

I wanted to design a custom spool holder for my Flashforge Finder printer, allowing me to use non-proprietary filament spools. After researching online, I discovered Phil_Read's outstanding design but found it too complex and decided to simplify it...

External Spool Mount for Flashforge Dreamer Printer. Instructions This design utilizes one (1) 5-6" long, 1/2"-13 bolt and one (1) 1/2"-13 nut inside the handle to secure the spool. Drill a 1/2" hole in the back plastic to allow the bolt to pass...