flashforge creator pro 2 upgrades 3d models

I've been using Hatchbox 1.75mm ABS filament, ordered through Amazon, for over a year now. Recently, they started shipping spools with a larger diameter, so I designed a new filament holder to accommodate the change. After several iterations, I found...

After a year, my printer began to exhibit z-wobble. The two rods were pressed in tightly at the top, while the bottom barely grasped them, with a significant 35mm gap between them. By printing pairs of spacers, I was able to lock the rods firmly in...

Created with Customizer at http://www.thingiverse.com/apps/customizer/run?thing_id=1108314. ... Instructions Using the following options: rod_pitch_angle = 0.1 slot_thickness = 20 hanger_height = 8 stopper_margin = 50 rod_diameter = 5...

My FlashForge Creator Pro was scratching up the floor due to one of it's original feet being ripped off so I decided to whip up a new foot to replace the original. ...Keeps it stable and keeps the floor safe.This foot fits the original screw and...

One of the extruder filament inlet caps broke off Flashforge Creator 3 printer, so I designed a replacement.

It seemed like a great fit for my FlashForge Creator X with metal frame, which is essentially the same printer as the FlashForge Creator Pro but without the plastic cover. After installation, the 5015 fan case was sitting about 3mm too high on my...

I've purchased the Ecubmaker Fantasy Dual Extruder Bracket directly from the manufacturer, and I'm interested to know whether it's compatible with my Flashforge Creator.

This Dial Indicator holder, designed for FlashForge Creator rails, features a central 8mm hole and two 6mm x 6mm magnet-holding holes. ...Simple to print and install.

New spool holder for old-type (wooden) Flashforge Creator. Fits standart 1kg filament spools. ...You should rotate holder model upside-down in your slicer.

3D printed - Integrated Extruder cover and Filament Guide for a FlashForge Creator 3. ...Both left and right covers are included in the files.

Upgrades for CNC 3020 or 3018 Pro MAX full metall. ... TPU details: 3020_Nut_damper_T8_0.8.3mf - for Z-axis 3020_Nut_damper_T8_0.4.3mf - for XY axis PLA details: 200W_slim_impeller_8mm.3mf

Customized version of https://www.thingiverse.com/thing:1949142 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1949142

Customized version of https://www.thingiverse.com/thing:1949142 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1949142

Print Settings: Printer: Flashforge Creator Pro 2016 / Makerbot Rep2 Rafts: Doesn't Matter Supports: No Resolution: 0.3 Infill: 15% Notes: There is no special setting or approach required to print this part. ...Simply use your default settings for the...

I developed this for my Flashforge Creator X, but it should work with any Flasforge Creator Pro or similar Makerbot Dual clone as long as the X carriage dimensions are the same. This assembly allows you to replace the original dual "MK10" extruder...

Here are IGES and STL files representing all the components I've measured and modeled so far for the Flashforge Creator-X extruder assembly. ...Next, I'll focus on modeling the actual extruder unit.

The slots are enlarged to accommodate a Flashforge Creator, and the spring slots are made larger for easier assembly. The slots are also more centered, necessitating a height increase so the printer's bottom clears the spring when in position. ...My...

Filament guide cap =============== Most simple and strong filament tube cap, that original. ... Specialy for flashforge creator 3 dual extruder printer. ... Recommended one tree-like support in centre of hole.

This is a Prusament spool holder / washer for a Flashforge Creator 3 printer I noticed there is a groove on the inner ring of the spool that jams as it unwinds this provides a smoother surface to roll on

Some Upgrade parts for the brand new AR Wing Pro. VTX Antenna Mount: Placed inside the side fuselage compartments in the frint inner corner. Screw on the SMA Pigtail. Glued in with some uhu por, E600, Gorilla glue or epoxy. Close hatch to get an...

This clever little gadget effectively silences the whining jet engine noise produced by the FlashForge Creator X when idle. The source of this annoying hum is a small 20mm fan at the bottom of the case, which cools the stepper motor drivers. I...

The 120mm fan mount attaches to the front of a FlashForge Creator for enhanced cooling, preventing PLA from drooping during overhang printing at 180C. Standard fan screws may not fit due to narrow holes; zip ties can be used as an alternative. A...

Coil Support Extension for 2.3 kg Users

This is my initial design submission for Thingiverse: a 3kg spool holder tailored specifically for my FlashForge Creator 3. The spindle is mounted at a 45° angle to the printer's body, and it features a 5° incline to prevent the spool from toppling...

So I salvaged a Flashforge Creator - possibly a Replicator Dual knockoff - along with a couple of cassette-like filament reels branded Colido and QiLive, whose standardization remains unclear... and figured it would be a good starting point to design...

... tube holder designed specifically for a QIDI Tech-1 printer. ... It's also highly likely to fit the Flashforge Creator since QIDI essentially replicated that printer's design. ... To print this replica, place it face down and avoid using any supports.

I'm holding two custom spool spacers alongside my FlashForge Creator. These spacers were designed specifically for this 3D printer and can be found on Thingiverse under the ID #970261. ... This model was created using Tinkercad, a powerful online CAD...

To prevent filament tangles on the FlashForge Creator, you can use varying-size sleeves to hold the spool almost snug but not too tight for easy turning. The sleeves come in different sizes to accommodate various spool thicknesses and 'wells'.

If you have any question  leave a comment and I will do my best to answer Nozzle cleanerThe hole for the poly is a bit under sized, use some force to convince it to go in.klipper config in the files.Hardware:Nema 17 Stepper driver AT2100Poly 16 teeth...

The cutout for the SD card in the wooden case of the Flashforge Creator is oversized compared to the SD card reader inside the unit. This often results in missing the reader altogether, causing the card to drop into the case instead. This...