flashforge creator pro 2 upgrades 3d models

A ~10mm spacer that I made to raise a slightly oversized spool that was rubbing on the lower surface of the Creator 3's stock side spool holder compartment. Can be scaled in the vertical axes in FlashPrint to make the spool sit higher or lower if...

I'm not sure which other Flashforge printers this design will work with, so if anyone has any knowledge on the matter, please share your findings and I'll update the tags and groups accordingly. ... Check out my friend's independent game company at...

If you're the creator and you're satisfied with this project, I'd appreciate it if you could give me a shout-out! ================================================================== For people like me who accidentally break the side flaps and don't...

This innovative solution is geared towards the needs of creators who want to build custom projects using the powerful capabilities of Raspberry Pi. With this housing system, users can connect cables easily, streamlining their workflow and allowing...

The creator has devised a means of securing filament tubes and cable management directly onto the print head, thereby eliminating the need for cumbersome clamps and cheap cable covers that often compromise their performance. The rear bracket cleverly...

The original spool holders of the Creator 3 won't hold those spools very well, they kept on leaning down with the risk of falling. Plus I couldn't close the side door without the spool being jammed. Solution: a 50mm OD and 70mm deep spool holder...

This bracket replaces the noisy little fan on Creator X, cooling the main board. Place it in place of the metal shield that sits underneath your printer. To work effectively, you'll need a 120mm computer fan - keep in mind, though, that the onboard...

... videos of crafts in progress. ...Its top clip is 6mm deep, fitting printers with 6mm lip edges. MakerWare settings include normal mode, 0.2 layer height, 230°C extruder temp, 110°C bed temp; raft use but no supports. ...Printed in red ABS plastic.

... Screw inset is set to 4.25 mm. Glass size is set to 1.8 x 203.2 x 247.75 inches. Screw diameter is set to 2.85 inches. Bed dimensions are set to 8.5 x 154 x 225 inches. Nut diameter is set to 6.5 inches. ...Supports are enabled with a setting of 10.

Print 2 holders and 1 spacer. Replace the screws on opposite corners of the heated bed with longer screws and a wingnut instead of regular nuts. The holder has a slotted design that allows you to adjust and tighten it securely against the glass. ...To...

... height allows for free movement of the motor. Credit goes to http://www.thingiverse.com/thing:124700 for the MotorEnd concept. Print Settings: Printer: CTC Rafts: No Supports: Yes Resolution: 0.2 Infill: 75% for MotorEnd, 40% for FrameEnd and Link

... better prints with a more consistent print environment, reduced warping and delamination. The complete kit is available at http://drazzticaction.com/products-page-2/3dprinters/enclosure-for-makerbot-replicator-2-2x-3d-printers-and-similar-clones/.

Hardware 2x625ZZ bearings 6 m3 long bolts (bought 65mm long and cut to size as I assembled it, maybe will measure them some time later ;) 3 m3 nuts 8 m2.5 bolts (from old laptop, case screws, they measure 2.5mm diameter about 5-7mm long) Belt used...

a spool holder for flashforge creator pro this one is dor hole diam. ...of 30mm

Something I threw together in Tinkercad to replace the terribly designed spools that came with the Flashforge Creator Pro.

The following version of the spool holder, inspired by Davedfx, has been adapted specifically for use with the Flashforge Creator Pro (2016). Unfortunately, the original recording diameter proved to be too small for my needs and has since been...

This Shim perfectly matches the Flashforge Creator X Pro's specifications, featuring a precision-cut 1/4 inch or 6.35mm build size specifically designed for mounting glass plates securely atop the heated build plate. For added stability, I've...

Remix of Mr Kee's shim for the Flashforge Creator Pro, designed specifically for use with a 1/4" glass bed plate. ...Modified to utilize the existing screw holes on the name plate flange, eliminating the need for additional hardware.

Print Settings Printer Brand: FlashForge Printer: Creator Pro Rafts: No Supports: Yes Resolution: 0.2 Infill: 25% Filament: Polymaker PLA Grey Notes: Print the model standing upwards with supports similar to the image in the listing. Rafts are not...

Spool holder for Flashforge Creator Pro 2016 2 x Screws, 3mm in diameter and 8-15mm long are required 31mm is the recommended diameter for 90mm wide spools If different sizes are needed, just let me know: editing takes only seconds Print Settings...

A versatile accessory designed to complement Raspberry Pi cases equipped with 75mm mounting holes, this innovative device attaches securely within the handle hole of the popular Flashforge Pro.

Filament support makes a huge difference in Flashforge's "Creator Pro" 3D printer performance. The filament tends to get stuck frequently, but this handy accessory resolves loading issues instantly. It seamlessly integrates with the sheath holder...

These are the parts i designed to optimize the use of single extruder mode on the FlashForge Creator Pro. This includes a top plate, fan duct and cable clip for use with right extruder only. Top plate uses an 1/8" NPT push to lock fitting for the...

The FlashForge Creator Pro (pre-2016) boasts a spacious print area illuminated by a 5-cm long LED strip. This strip is energized by a budget-friendly Chinese DC-to-DC converter, which efficiently steps down the voltage from 24V to 12V. ...To ensure...

The edge is angled to prevent the spool from falling off and the spool holder provides a simple, minimalist design that gets the job done. Enjoy! Print Settings Printer Brand: FlashForge Printer: Creator Pro Rafts: No Supports: Yes Resolution: 0.2...

FRLa Flashforge Adventurer 5M Pro est une imprimante 3D qualifiée très silencieuse, mais une mauvaise conception du support du ventilateur refroidissant les steppers vient perturber le résultat. Ce support permettra une fixation plus stable de ce...

This is meant to be a full ventilation kit for a Flashforge Creator Pro. You will need to print: -Top Replacement pieces for FFC Pro: FFC PRO Vent Top Left and Right (2 pieces total) -Duct to mount to top of new FFC Pro Top: 4in Vent adapter from...

A simple re-design of the spool holder for the FlashForge Creator Pro. The barrel is longer and smaller in diameter which allows for smaller and wider spools, increasing the compatibility of spools that can be placed behind the machine for a cleaner...

An exhaust manifold for the Flashforge Creator 3 Pro. This attaches to the back of my Creator 3 Pro to a 4" AC host and runs to a connector leading to outside my house. I have included the drawings for the manifold and the 4" host coupler ends as...

Work In Progress \r\n\r\nRefurbishment of Flashforge Creator Pro (pre 2016) Bed Support and Z Axis Screw.\r\n\r\nBed Support Upgrades: Aluminum PA9, 6mm thickness for enhanced stability.\r\nScrew Replacement: High-precision Ballscrew 1204 for smooth,...