flashforge creator pro e3d v6
112896 3d models found related to flashforge creator pro e3d v6.thingiverse
UPDATES 09/10/21 - Added a mounting for a 5015 style blower fan. This is a remix of both https://www.thingiverse.com/thing:1350343 & https://www.thingiverse.com/thing:3547317 I remade the X carriage to have only three bearing mounts, this...
thingiverse
Go here: https://www.extra-life.org/participant/385519 This is a direct-drive adapter that will fit the FlashForge Creator Pro printer with the E3D Cyclops extruder. **WARNING:** Do not perform this upgrade on your primary or sole 3D printer. It...
cults3d
Go here: https://www.extra-life.org/participant/385519 This is a direct-drive adapter that will fit the FlashForge Creator Pro printer with the E3D Cyclops extruder. WARNING: Do not perform this upgrade on your primary or sole 3D printer. It is...
thingiverse
This will allow you to use a E3D V6 and Titan extruder on your FFCP ( NOT TESTED ON OTHER MACHINES) Used a pancake stepper motor as a standard one hits the back of the machine but you can tape a block on the left Y carriage to hit the end stop if you...
thingiverse
A simple clip to hold the door up on a FlashForge Creator X Pro.
thingiverse
A voxelized version of the FlashForge Creator Pro, Modeled in MagicaVoxel.
thingiverse
Flashforge Creator Pro spoolholder . ... Diameter 25mm (29mm end) and length 89mm
thingiverse
... was created by ajwammock as a door handle replacement for the Flashforge Creator Pro. Please post any prints so I can see how it works out for you. Print Settings Printer: FlashForge Creator Pro Rafts: No Supports: No Resolution: .20 Infill: 20%
thingiverse
A simple clip for a 1/8" (about 3mm) glass plate for the FlashForge Creator Pro. I didn't want to deal with wing nuts every time I change out a new glass plate on top of the printing bed so I made some easily removable clips. ...You can use 2 or 4 to...
thingiverse
I remixed this Because i put this thing on my Flashforge Creator PRO and when it got to the sides the wires and hte tubes got hung up a little bit so I just made a longer one :) good design just needed to be longer. ...Thank You :)
prusaprinters
I had a splash of acetone wipe out the FlashForge Creator Pro logo on the front of my machine, so I printed up a replacement. I've also included an inverted version.</p> <p>This one was printed on glass with an ABS slurry. ...In hindsight, I should have...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=40705 Instructions Using the following options: hole_radius = 2.5 icon_rotation = 0 manual_width = 100 manual_length = 100 icon_size = 12 icon = 0 Font = write/orbitron.dxf message_one =...
thingiverse
These are parts that i have made to enhance the use of my FF Creator Pro printer * Replacement spools for the FlashForge Creator Pro, along with a wall mountable holder * If you don't use the factory filament you're going to need these. * If you buy...
thingiverse
... CAD tool to add your own features. Enjoy! Print Settings Printer: Flashforge Creator Pro Rafts: No Supports: No Resolution: 200 Infill: 100 Notes: Wood filament at 200 degrees C for extruder and 50 degrees C for bed. ... Keep it slow, around 40mm/s
thingiverse
I had a splash of acetone wipe out the FlashForge Creator Pro logo on the front of my machine, so I printed up a replacement. I've also included an inverted version. This one was printed on glass with an ABS slurry. In hindsight, I should have...
cults3d
I had a splash of acetone wipe out the FlashForge Creator Pro logo on the front of my machine, so I printed up a replacement. I've also included an inverted version. This one was printed on glass with an ABS slurry. In hindsight, I should have...
pinshape
I had a splash of acetone wipe out the FlashForge Creator Pro logo on the front of my machine, so I printed up a replacement. I've also included an inverted version. This one was printed on glass with an ABS slurry. In hindsight, I should have...
thingiverse
If you feel that the edge of FF creator pro's handle on both side is too sharp. ...This insertion handle is for you.
thingiverse
This is a remake of the classic FlashForge Hood, readapted for 5mm plexi. ...
thingiverse
A simple plug to fill the handles in the flashforge. However this one allows you to insert a common thermometer so you can monitor internal temps while printing high temp ABS, Nylon etc. The thermometer is the dirt cheap kind you find all over ebay...
thingiverse
After I received my FlashForgeCreator PRO printer, I realized that steppers got very hot during print. I designed Snap - On - Holders for the Steppers. I used standard 24V - 40x40mm Fans from local electronic store and connected direct to printers...
thingiverse
a Large spoolholder for a Flashforge Creator Pro
thingiverse
... OEM extruder assembly. Use the E3D V6 extruder. Follow my project here: https://crunchysann.com/BL/projects/ Print Settings Printer Brand: FlashForge Printer: Creator Pro Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.3mm Infill: 20%
thingiverse
Simple plug to cover the handles on a Flashforge Creator Pro (not the newest version). ... Print Settings Printer: FlashForge Creator Pro Rafts: No Supports: No Infill: 15% Notes: .3mm Layer Height, ABS, Simplify3d
thingiverse
These hooks fit nicely into the handle of your flashforge creator pro, helps reduce clutter around your printer!
thingiverse
... ...I therefore created a new bracket based on similar work for other Flashforge 3D Printers Print Settings Printer: Flashforge Creator Pro (2016) Rafts: No Supports: No Resolution: Low Infill: 15 % Notes: Printed using PLA at 205 degrees Celcius