flashforge creator pro e3d v6

<p>I like TPU for these. ...&nbsp;About 25 percent infill, and no supports required..</p>

After a few months of using my 3D printer decided to redesign the cooling fan nozzle to be sure that the main air stream goes to the edge of hotend not higher as designed by default.Materials needed 2 M2x16 screws to hold the top and bottom together2...

This adapter mounts to the original spool holder allowing you to use third party filament reels.

Snap in filament guide tubes securely into place by aligning them with pre-existing screw holes on the frame. ...Replace M4 screws with new ones that are a bit longer for added stability.

Customized version of www.thingiverse.com/thing:116104 Created with Customizer! ...www.thingiverse.com/apps/customizer/run?thing_id=116104 Instructions Using the following settings: Wall width is set to 2 Shapes will be removed as per...

I use these blocks to achieve nearly perfect leveling of my printer bed. I created them at 0.395 inch thickness, but each nut needs a half turn adjustment after setting the bed with these blocks. Ideally, 0.400 inches would make it perfect, and all...

I was looking to attach my Logitech C270 webcam to the front of my printer, and I wanted a solution that would be compatible with the printer door being either open or closed. Many of the available mounts required the door to be shut in order to...

layer 0.2 support on table need glue

To minimize rattling and airflow through an acrylic hat.

Securely fasten the extruder cable to the filament tube, ensuring a tight and stable connection.

This is a remix of the object https://www.thingiverse.com/thing:1860297 modified and adapted to pass the filament from a reel hanging on the wall or under a shelf. ... It is used in conjunction with another printed item and found here on thingiverse.

Fine-tune your printer on the fly by adjusting the bed level using the convenient knobs located underneath, allowing for real-time adjustments to achieve optimal print quality. ...Print seamlessly without worrying about interruptions, thanks to this...

I carefully crafted this clip to remain securely in place without hindering the Plexiglas hood's functionality. The design ensures a precise fit within the frame's top corner, guaranteeing no interference with the transparent cover. ...Its flexible...

I'm reworking the mount on the chassis, securing it with two M3 screws. ...I initially printed a prototype, but it shattered when I attempted to install the camera.

This model was crafted using Tinkercad's robust design capabilities. ...It can be easily edited and refined online at https://www.tinkercad.com/designs/hEiUfYKuyKY.

I managed to overcome the initial challenge of printing the original design vertically, despite the limited height clearance on my printer. To achieve this feat, I cleverly divided the complex model into two manageable sections using TinkerCAD's...

Upgrade those cheap hinges for improved functionality. These replacements perform admirably without additional components. To achieve seamless integration with your printer, install a strong magnetic latch on the door. Optimizing print settings by...

Thanks for the original design! Had to tweak it a little for my purpose. Made this remix to level the dual extruder on my 2016 FFCP. Steps to use: 1: Remove all filament and allow nozzles to cool 2: Remove parts cooling fan and duct 3:...

A standard attachment for the FFCP 2017 glass surface upgrade. (~3mm Glass) Securely place on its side, allowing it to snap into position on top of the glass surface. ...The flat part should make direct contact with the glass, facing away from the...

Just a Simple Spacer to Plug in the Handle Hole and Possibly Retain a Bit More Heat in the Build Chamber.

I've had to modify the M3 inserts because they're too small in diameter and just float around in the existing holes, so I ended up shrinking down those holes for them. When it comes to the original design, I suggest printing it with ASA or ABS or...

I figure it's time to retire that old Flashair card now that I hardly ever use it. ...It's been collecting dust for far too long, so I think it's only fitting that I cover it up and let it rest in peace.

The air duct is very simple and directs air precisely to the place of printing under the nozzle and not on the nozzle itself as in the stock, print it with a thickness of 0.1, the plastic does not matter, set it so that it does not touch the nozzle.

<p>Other z axis shims did not actually trigger the z axis switch, this should do the job. Still have to print and test. ...Will update when I finish it.</p> <p>Update: Modified the shim, I removed the old one and the one currently uploaded works without...

I tweaked the file so the filament tube won't come crashing down anymore. ...Built a tiny shelf for the tube to safely rest on, securing it firmly in place.

clips/snaps over the top of the printer handle area for top mount spools

I enjoy printing on a glass because it allows me to replace the print surface quickly and keep working without waiting for the print bed to cool down completely. I've tried various clips available from Thingiverse, but I encountered two significant...

Firstly acknowledgement goes out to rowokii for creating the Spool Holder & Clip on Thingiverse, accessible at https://www.thingiverse.com/thing:767317. My goal was to gain visibility into my spools' activity, which is impossible with the standard...

I encountered substantial challenges printing the initial component using ABS, as the layers frequently detached at the male threads. Increasing the print temperature to enhance adhesion resulted in distorted threads. ...Consequently, I imported the...