flashforge creator x 3d models
346665 3d models found related to flashforge creator x.thingiverse
... wrench multitool and and hand-sized LED flashlight. All tool slots are angled on the top for better access and more secure storage. Instructions This tool holder fits the side wall of a FlashForge Creator X using the carrying holes on the side.
thingiverse
... machine uses three of these and one wider mount. Remove the brass inserts from the broken axis and snap them into these with some pliers. Print Settings Printer: Flashforge Creator X Rafts: No Supports: Yes Resolution: .30 Infill: 100% Notes: 255° F
thingiverse
... http://www.thingiverse.com/thing:1664580 Remove the brass inserts from the broken axis and snap them into these with some pliers. Print Settings Printer: Flashforge Creator X Rafts: No Supports: Yes Resolution: .3 Infill: 100% Notes: PETG 260° F
thingiverse
This one was created for a Flashforge Creator X backfit with the Creator Pro's metal build platform but should fit any of the many bots which use a similar metal stage. It fits over the rear lip and so won't be appropriate if your bot has a fancy...
thingiverse
This is a holder for the cooling fans and heatsink on the flashforge creator x to place them in the rear of the extruder instead of the front of the extruder. This gives you better access to see how the filament is feeding into the nozzles and still...
thingiverse
After installing, the 5015 fan case was sitting about 3mm too high on my FlashForge Creator X - with the result that the fan would definitely crash into the printer metal frame before hitting the Y-axis limit switch located at the top right rear of...
thingiverse
This handy little device helps to quiet the jet engine noise the FlashForge Creator X makes while idle. The source of the noise is a small 20mm fan on the bottom of the case that cools the stepper motor drivers. I designed this during the summer...
thingiverse
This is switch mount for the Creator X, but it might fit on the Creator Pro. Recently I installed the Creator Pro platform in the Creator X. This means the old style clip on spacers wont work anymore. This piece will allow you to remount your switch...
thingiverse
This is a bracket to replace the noisy little fan on Creator X that cools main board. Just place it instead of metal shield of the board underneath the printer. You will need 120mm computer fan. Just remember, that onboard voltage is 24V!!! You will...
thingiverse
Primary issues I'm working on resolving is adding print cooling and getting a better fit/seating of the assembly in the Creator X chassis. ***12/3/18-This model is lacking a cut away I did by hand on the back side to allow it to sit flush more...
thingiverse
I also only use one extruder on my Creator so I took off the fan from my second extruder and put on this shroud. I've gotten really good results with this design. The only drawback is that the fan is on at all times but this hasn't reduced my print...
thingiverse
Cable chain to prevent X-Axis motor/limit switch cable wear. Print 12 of the Link part, one FrameEnd part and one MotorEnd part. Assemble the links by pushing together on a flat surface and they will snap securely into place. Don't attach the link...
thingiverse
These are a nice set of matching acrylic doors for the Flashforge Creator X style Replicator clones. The doors consist of a left and right side (mirrored), with four low profile 3D printed hinges and a 3D printed latch that holds both doors securely...
thingiverse
Fits the Flashforge Creator X and Pro printers (and possibly others that have 34mm nozzle spacing) with the stock 6mm PTFE guide tubes. Version 2 adds a support structure for the cable bundle with provisions to install one or two cable ties. The...
pinshape
SummaryThese are a nice set of matching acrylic doors for the Flashforge Creator X style Replicator clones. The doors consist of a left and right side (mirrored), with four low profile 3D printed hinges and a 3D printed latch that holds both doors...
thingiverse
Spacer Block to add 3mm plate glass for heating bed on Flash forge Creator X. ...Spacer activates limit switch early to allow 3mm glass.
thingiverse
Print Settings Printer Brand: FlashForge Printer: FlashForge Creator Pro Rafts: No Supports: Yes Resolution: Medium Infill: 20% Notes: Printed using PLA, 230C with heated platform @ 60C. Post-Printing Note the two nuts that sit under the platform to...
myminifactory
Print this wingtip M3 nut in ABS using 0.25mm layer height with 20% infill. ...It is a replacement to the existing knurled nuts that comes with the FlashForge which is difficult to use when levelling the hotbed.
thingiverse
I'm about to do a hot end upgrade and made a snap on extruder leveling tool. It is set exactly where my current nozzles are set. ...Print it so that the space from the bottom of the hooks to the top of the floor are 37mm apart.
thingiverse
If you made this thing and are happy with it I kindly ask to give it a shout! ================================================================== For dumbs like me who are breaking the side flaps and do not want to print the whole frame-end again. For...
thingiverse
Covers the side panel hand-hole openings when it's time to enclose the build chamber. Works as well as duct tape and looks a lot better! Instructions Just print and install. ...They should pop right...
thingiverse
The original feed pipe clip is too close to the machine, sometimes the filament pluck into the spool and stuck everything (especially whenever my print completes 90%). So I made this as a replacement. I uploaded the CAD file so if it doesn't fit...
thingiverse
Shim for using a 1/4" glass sheet on the build plate. ...Adapted from: http://www.thingiverse.com/thing:263804
thingiverse
Print in ABS (those extruder motors get HOT), and reuse the OEM self-tapping screws on this piece. ...Use a bit of extra temperature to get a bit more strength for the screw hole cylinders.
thingiverse
Users of Flashforge Creator X who prefer to use 3mm glass plate can use this shim to compensate for the glass plate thickness. Creator X build plate is much thicker than the wooden Creator so adjusting the screws would not work. Lowering build plate...
thingiverse
Here are IGES and STL files of the parts I have measured and modeled to represent the parts that make up a Flashforge Creator-X extruder assembly. ... I will work on getting the actual extruder modeled soon.
thingiverse
A smaller spool holder for the Creator Pro X. The default ones are huge and don't fit custom filament. This prints without rafts or support, in two separate pieces. Print the Left and Right separately and they snap perfectly into the FlashForge in...
thingiverse
... to the frame as shown in the photo. The link and Motor-End are still the same and are fitting perfectly on the Flashforge creator pro. Print Settings Printer: Flashforge Creator Pro Rafts: No Supports: Yes Resolution: 200 micron Infill: 45%
thingiverse
This is a tool hook that mounts onto the handle of your flageforge creator printer. It holds a scraper and a set of calipers and four SD cards. what is new in version 2: added better dimensions for calipers added sd card holders added...
thingiverse
The major problem, the stepper for Y motion is set lower than in the creator and the chain keeps the Y axis from homing (bummer). So, I fired up sketchup and changed it around and presto works great. I then ran into another obstacle. I wanted the...