flashforge files 3d models

I got tired of forgetting the filament type and color currently loaded on my FlashForge Creator PRO 2 IDEX machine and having to fumble around the back of the printer to read the spool labels. So, I designed a small plate holder for each side, and a...

## Recommended Print Settings Main Unit: 0.25 res, 20% infill Raiser : 0.25 res, 10% infill 19mm Axle: 0.12 res, 15% infill Adapter Rings: 0.25 res, 100% infill Single Adapter: 0.30 res, 100% infill (new) - Recommended print settings are also noted...

This remix of the FlashForge Creator Pro Filament Alignment Bracket by Makersome has been completely rebuilt from scratch using the original designs to fit the new FlashForge Creator Pro 2016 model perfectly. I originally printed Makersome's design...

Because FlashForge printers use the same extruder mount block I'm sure it works on FlashForge Creators, too. You will need the following parts to mount my Active Cooling Fan Duct with this clip: 2x M3 nuts 2x M3x14 hex screws (or alternatively...

This is a Simplify3D printer profile file for the Flashforge Creator Pro and its CTC clone counterpart. I've tweaked the startup script to initialize all axes while maintaining front right corner heating. Next, it purges the right side of any debris...

With just a dash of glue and a speedy installation, it's now feasible to employ the European-style spools that carry an impressive 750 grams of filament. However, avoid using these spools for heavier 1 kilogram loads. A close examination of this...

Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069

The design incorporates a curved groove to securely hold cables out of the way and away from getting tangled under the cover.

I've made life a whole lot simpler by swapping out filament guides for 3D printers with direct top feeding instead of rear feeding. This upgrade reduces parts and eliminates complicated setup, making it the ideal solution to eliminate unnecessary...

This is version 2 of my nozzle light, utilizing two 12-volt LED strip segments wired in series directly to the 24-volt supply via a 100-milliampere fuse. The front and rear LEDs illuminate the area beneath the nozzle, allowing for clear visibility of...

Safety Blinds for Installation of Fuse Holders For Heating Bed and Extruder Fuses. ... Compatible with fuse holders from Reichelt such as https://www.reichelt.de/sicherungshalter-fuer-5-x-20-mm-250-v-10-a-schwarz-s-313903-p245383.html?&nbc=1 ...

This plug creates a tight seal when the spool mount is not installed, effectively enclosing the build chamber for enhanced stability. For simplicity and optimal fitment, I designed this one with usability in mind. ...A similar design filling the handle...

This basic plug fits neatly into a handle and completes a fully enclosed build chamber, providing a simple yet effective design that adapts well to most printers. Other designers have come up with impressive designs too, but I chose this one for its...

Staying true to Stayduned's original concept, I've tweaked the design for an even smoother assembly process and incorporated Siyanaks' ingenious holder (available at Thingiverse as #2817282) for unparalleled stability without relying on a magnet. ...The...

I added an LCD casing to my CTC device, enhancing its appearance. ...It now looks more appealing!

A versatile device for redeploying high-temperature 3D printing cartridges.

I recently replaced my 40mm MB Fan's annoying whine with a 60MM fan on my FF, which finally got mounted with more than just a cable tie and some tape. The first attempt wasn't ideal for many reasons, but it helped me design V2, which is what I'm...

I've noticed that many spool holders fail to keep the spool upright and also position it too far away from the printer, allowing filament to snag. ...This design minimizes the gap between the spool and printer, ensuring a smooth operation, so a pin...

I've seen some designs for the Dreamer and Dremel, but I didn't want to drill into the case or have it compromised so I couldn't use the top lid. My design requires no modifications to the machine and can easily be restored to its original state if...

Toughened up the cable holder sleeve to prevent tie wrap slots from over-stressing it and causing a break when removing it from the printer, which was a worrying sign. The same design gets more robust with a beefier cable sleeve. ...Print Settings...

Here is my revised input: I've created an updated shim for Z axes sensors when installing a 6.5mm thick glass platform, allowing me to position it precisely at 7 for more relaxed screws. ...Moreover, I added slots in the new design to provide extra...

I designed the spool holder for https://www.thingiverse.com/thing:2268148 that relocated the spools from the back to the front and top, requiring an easy way to route filament to the extruder, so I came up with this solution. I added a 10-foot PTFE...

I purchased a refurbished Full Frame camera and found it didn't come equipped with a handle. In order to address this issue, I took on the task of creating one from scratch. A quick DIY project yielded a functional handle that boasts holes for...

Enable Printing of Details.

Bed nut must undergo a critical heating process before being inserted into its designated hole, where it will be securely fastened in place. ...When printing with ABS material at 3% below standard size, an allowance for shrinkage is required.