flashforge finder enclosure 3d models

Simple center finder for workpieces up to 10 cm wide with 7.6 mm hole for a pencil with marking gauge 2-20 mm.

Print Settings Printer Brand: FlashForge Printer: FlashForge Creator Pro Rafts: No Supports: No Resolution: 0.20 Infill: 20% Notes: Print rounded side at bottom at slow speed in PLA@200 bed 60. Adjust scale slightly if you need to (differences...

Print Settings Printer: Flashforge Dreamer Supports: No Resolution: 0.2mm Infill: 40% Notes: Printed with Prima3D Value black PLA at 0.2mm resolution with 40% infill, sliced with Simplify 3D. Post-Printing The grey plastic of the Flashforge Dreamer...

... standard with many Meade telescopes, including the ETX series. ... I created this adapter to attach a piece of solar filter from a pair of solar glasses directly to the finder of my ETX90 before capturing an ISS solar transit with a high-speed camera.

This is a precision-built finder scope engineered specifically for pinpointing the sun's location through any standard telescope. ...Its sleek design effortlessly adapts to the TELRAD finder base, making it an ideal accessory for the highly anticipated...

The telescope finder and laser bracket combines the functions of a finder scope with a red dot laser sight, allowing users to effortlessly align their telescope with celestial targets. ...This innovative design makes it easy for beginners and seasoned...

These are shims used to elevate the rear of the Celestron Red Dot finder scope so it can align with the target point of a Celestron telescope. ...I utilize these on my Celestron 130EQ because I discovered that the finder scope ran out of adjustment...

Visit http://www.instructables.com/id/3d-Printed-Medical-Vein-Finder to check out a 3D Printed Medical Vein Finder. You can vote for the project in the contest there. ...For any questions, email cosminaschiteanu@gmail.com or alex_stanciu2003@yahoo.com.

Print Settings: Printer: Flashforge Creator Pro Rafts: No Supports: No Resolution: 200 microns Infill: 100% Notes: For optimal results, use wood filament at 200°C for the extruder and 50°C for the bed. ...A slow print speed of around 40mm/s is...

Spool holder for the Flashforge Inventor. This allows for bigger spools to be used in the machine. This is for max 198mm spools with 53mm hole and 64mm width. If you use something else, please check that it really fits before using. Yes you can...

... this spool holder, including full support and raft, is around five hours and thirty minutes on standard resolution settings. Print Settings: Printer Brand: FlashForge Printer: Creator Pro Rafts: Yes Supports: Yes Resolution: Standard Infill: 30%

Flashforge Creator Pro - Spool Holder Uses standard mount holes on the back of the machine. This design uses two 608 bearings in the cylinder that contacts the spool. I do recommend printing this in PETG due to the need for increased strength. ...

Here is a revised design for an external spool holder that fits seamlessly into the FlashForge Inventor. This innovative accessory allows you to keep your filament neatly organized on the side of the printer, eliminating tangles and messes. The...

This is a simple-rotating spool holder designed specifically for the FlashForge Creator Pro and similar 3D printers. The outer tube rests smoothly on its bearings. A convenient clip lets you attach different size spools up to 10 cm in diameter with...

I came up with this idea from combining my Dragon keychain with the Flashforge Door open clip that I made earlier. To integrate them seamlessly, I chose to modify the same clip by rounding one end to create a perfect fit for attaching the Dragon to...

Change Log: 02/14/16: Increased mounting screw pass-through diameter to 3.4mm, making it easier to pass through Print Settings Printer: FlashForge Creator Pro Rafts: No Supports: No Resolution: 260 micron Infill: 50% Notes: IC3D White ABS No Raft No...

I had a sudden splash of acetone erase the FlashForge Creator Pro logo from the front of my machine, so I set out to design and print a replacement. I've also included an inverted version for good measure. This particular one was printed on glass...

**Updated to explarge gap between extruder arm and runout sensor** This is an adapter plate to allow swapping the stock Flashforge Adventurer 3 extruder with a genuine Creality Ender 3 metal extruder kit...

I keep needle nose and regular pliers, a caliper, a flashlight, and two tubes of superglue stored under the flashforge, where it's been getting cluttered with electronic boards. To tidy up this mess, I built a caddy. This print requires sturdy...

I recently had a splash of acetone remove the FlashForge Creator Pro logo from my machine's front panel, so I printed out a replacement. Additionally, I've included an inverted version for reference. This particular print was done on glass with an...

This is a custom build based on http://www.thingiverse.com/thing:1897363 to utilize the arms for holding a Logitech HD Webcam C310 on the Flashforge Dreamer. To attach it, replace the top screws with M3x20 or M3x15 screws and secure the Dreamer in...

This is a custom-made hole plug designed for the Flashforge Creator Pro. Its primary function is to prevent foreign objects from falling into the printer's bottom chamber while also maintaining organized wiring. The plug was crafted using ABS plastic...

This ELP camera holder simply slides onto the "flashforge" plate, requiring no additional setup. Using ABS material and supports yields impressive results. The outcome is a sturdy solution that effectively holds the camera in place. A special thanks...

I got a splash of acetone to completely remove the FlashForge Creator Pro logo from the front of my machine, so I printed out a brand new replacement. I've also included an inverted version. This one was printed on glass with an ABS slurry. In...

... "Any Cubic Photon save resin platform bracket". https://www.thingiverse.com/thing:2930511 I didn't see any Resin saving brackets for my Flashforge so I used some inspiration from a few other designs that I saw and created one of my own. ...

... start creating your 38mm spool holder design using the Part Design Workbench in FreeCAD. Use the tools provided to shape your object as needed, paying close attention to dimensions and detail for a precise fit with your Flashforge Pro printer.

https://www.thingiverse.com/thing:2930511 I didn't see any Resin saving brackets for my Flashforge so I used some inspiration from a few other designs that I saw and created one of my own. (((UPDATE PENDING))) I need to rework the geometry of the...

... On the Flash Forge, you'll need to print the hollow bolt filament guide and drill a 3/8-inch hole in the lower corner of the printer enclosure. ...These spool holders work quite well for Makergeeks.com, Hatchbox, and MatterHackers' filament spools.

I needed some rubber feet for my Flashforge Dreamer printer. I should print this design (x4) in SemiFlex (if possible) or NinjaFlex. Instructions To print these rubber feet properly, use about 4 shells and a 25%...

This is a remix from http://www.thingiverse.com/thing:1897363 because I wanted to use the arms to hold a Logitech HD Webcam C310 on the Flashforge Dreamer. Use M3x20 or M3x15 screws to replace the two screws in the top of the Dreamer and screw it on...