shimano tl fc16 3d models
6698 3d models found related to shimano tl fc16.thingiverse
I added a 1/4 inch square hole in the back of the tool, to be able to use a ratchet and get more leverage when undoing a stuck pre-tensioning cap. ...You don't need extra leverage to tighten the cap, since it only requires 0.7 - 1.5Nm of torque to...
grabcad
A CAD file of the crank replacement tool was optimized utilizing Abaqus software, targeting affordability for printing. ...Despite its lightweight appearance and creation on an inexpensive 3D printer, it exhibits remarkable stiffness with a weight of...
thingiverse
... Holowtech II crank. ... Can be used by hand, with a 23mm spanner. or with a 5mm allen key. Herramienta para colocar y quitar el tapón de la biela Shimano Holowtech II. Puede usarse con la mano, con una llave de 23mm. ...o con una llave allen de 5mm.
thingiverse
Shimano Hollowtech II TL-FC16
thingiverse
This tool enables you to fine-tune the Bottom Bracket's axial clamping force for Shimano Hollowtech II cranksets, ensuring optimal performance and durability.
grabcad
This device enables fine-tuning of the non-drive side crank arm's bottom bracket bolt on Shimano Hollowtech II cranksets. ...Losing mine means I can print new ones via 3D technology whenever necessary.
thingiverse
Human engineered an altered design with a non-collapsed base, simplified printing capabilities.
thingiverse
Easier to print. ...No supports needed Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator 2 ...
thingiverse
Therefore, per Shimano specs and instructions, the cap must be first tightened to the spec and then the crank retaining bolts tightened. I did not have a 1/4" to hex drive adapter, so I remixed the original to have a standard 1/4" drive...
cults3d
This tool can be used to loosen that Torx-like cap, which is holding the left crankarm on the bottom bracket spindle (see picture). This is needed to swap/clean your crankset or replace the chainrings. The video here explains how to remove your...
thingiverse
Use this tool to unscrew the Torx-like cap on your left crankarm, attached to the bottom bracket spindle (as shown in the image). This action is necessary for swapping or cleaning your crankset or replacing chainrings. View a video demonstrating...
thingiverse
I remixed this tool to fit my torque wrench. Not many other people will have a wrench that works at 0.5 - 1.5 Nm, but here you go anyway. I also reworked it to print a bit easier, got rid of overhangs and chamfered the finger wheel. ...Enjoy
thingiverse
I required an instrument to tighten my Shimano crank bolt securely, therefore I designed and built this easy adapter to change to a hex driver. It fit perfectly onto the crank on the initial attempt. ...Enhanced with a circular shape for grasping...
thingiverse
This is a Shimano Tool (TL-FH16) to Install the outer seal Ring (Y3FM26000). ...For use with Shimano microspline freehub FH-M8110-BS, to set the correct deep.
thingiverse
This is a custom tool that shimano uses to fix the lock-ring onto the chain ring on shimano steps electric bicycles. I changed the sizes slightly for a better fit on the nut and to fit within the plastic chain ring guide. This design also uses a...
thingiverse
I inspired from Shimano TL-FC16 Hollowtech II Crank Arm Removel Installation Tensioner Tool. ... https://www.amazon.com/Shimano-assembly-FC-960-Ultegra-TL-FC16/dp/B097BJB8Z8
thingiverse
This should get you out of trouble if you need to tighten/loosen the chainring on an E8000 Shimano motor. ...I don't think it would last long term but go me out of trouble.
thingiverse
For those wishing to remove the front chainwheel on a Shimano STEPs ebike you need a tool to remove the left hand threaded lock ring. This ring is a different size to the usual shimano bottom bracket tool. Print Settings Printer Brand: ...
thingiverse
This tool helps you to remove the chainring of your shimano steps ebike. You'll need a 32mm spanner/socket wrench to turn the tool. NB it's a left-hand thread, so turn right to loosen! This remix from pvdm's version adds a smaller hole. You can...
thingiverse
Shimano TL-FC24 bottom bracket puller adapter, for SM-BB9000. ... Shimano TL-FC24 bottom bracket puller adapter, for SM-MT800.
thingiverse
Shimano TL-LR15 (cassette puller) amazon.com link: https://www.amazon.com/Shimano-TL-LR15-CL-Rotor-lockring-tool/dp/B000F5LLAS bike-components.de link: https://www.bike-components.de/de/Shimano/Kassettenabzieher-TL-LR15-p1086/
grabcad
The Shimano TL-PD40 pedal tool requires the use of a 22mm socket wrench for operation.
thingiverse
A time-saving alternative to the Shimano TL-FC32 Installation Tool, made possible by including the TL-FC25 Adapter, which comes with compatible Shimano BSA bottom brackets. By minimizing the need for purchasing frequently used bike tools, one can...
pinshape
The key for Shimano pedals, an analog of the Tl-PD40, is also suitable for pedals of other manufacturers. ABS, 3 perimeters, 35% infil
thingiverse
Stronger design with higher wall thickness throughout and reinforcements at the relevant points. ...Fits perfect on my Shimano Steps Lock Ring (Y78N00085, Drive Unit DU-E6100). ...
thingiverse
This tool is designed for efficiently tightening (or dismantling) Shimano pedals such as the PD-540 SL and PD-5600 SL models.
thingiverse
Scaled down version of the TL-FC32. Fits the newer BB-MT800 and other smaller Hollowtech II bottom brackets. Printed with 7 Shells and 50% Infill. ...Works nicely, fit is a bit loose, could be scaled down a bit, maybe 1-2%, but works as-is...