flashforge spool adaptor 3d models

To accommodate my spool holder's restrictive holes, I opted to create a custom spool for my 618 nylon spools that utilize the same size of filament, 1.75 mm. A central hole of 32 mm will adequately serve most printers in this setup. **Assembly...

... thought that it might be useful. ...I have a Qidi Tech 1 and X-Pro, I just tested it on the Tech 1. It fits a 1kg printer spool perfectly, with some slack, so should work with other 1kg Spools. ...You will just need an M10 x 50 bolt, nice and simple.

This adapter is meant for BaronWilliams's Large Spool Holder, available here:http://www.thingiverse.com/thing:415744 A straightforward spool rod cover was designed to be oversized with a lip on one side. This allows ProtoParadigm filament use inside...

These hub adapters should work with any 57mm or wider spool hubs. So long as the spool is less than 60mm wide. You shouldn't need supports, print with the wide side of the adapter oriented to the build plate. ...Infill is up to you, I did 15% ...

Updates: Current version (0.01) tested successfully with 50% of my spools, but the arm is too thick for some smaller spools. Resized version for smaller spool axles en route soon. 0.01 - Upgraded to enhance the arm and make it larger (if you have the...

... ...I tested it on my Tech 1 and found that it fits a standard 1kg printer spool snugly, with some extra room to spare, so it should work just as well with other 1kg Spools. ...All you'll need is an M10 x 50 bolt, which is quick and easy to install.

... supports. ...Tech3dp's remix of the spool drum accommodates filament rolls with a 30mm inner diameter. ...The spreader and 50mm diameter drum remain unchanged from tech3dp's original designs as found at https://www.thingiverse.com/thing:2790290.

I noticed there is a groove on the inner ring of the spool that jams in the printer as it unwinds,this washer provides a smoother surface to roll onUpdate: 18-02-2022 the hole is wider in the 35mm and 60mm version

This printer maintains optimal filament flow by applying precise pressure to the spool, ensuring that incoming filament wraps cleanly around previous layers without tangles or knots developing during printing. ... In an upcoming iteration, this feature...

You'll need: 1x M5 bolt, a minimum of 20mm long but ideally up to 30mm 2x 608 bearings Spool specifications include: Maximum diameter: 200mm Maximum width: 80mm (when using the longer bolt) Internal diameter: 20-60mm (with large bolts and nuts, it...

The key alteration to this design lowers the spool's top edge to match the printer case height, making it a perfect fit on my shelf. To accommodate my larger rolls, I slimmed down the bracket width from 40mm to 30mm and extended the rod length...

The main change to this design is it drops the top of the spool down to the height of the printer case. Allowing it to fit on my shelf better :) I reduced the width of the bracket from 40mm to 30mm and increased the rod length to accommodate my wider...

This spool stand can accommodate nuts being inserted between it and the printer's base plate. Screws may be installed in a reversed position. This setup makes swapping future revisions to the stand easier, eliminating the need to remove the entire...

The key modification made here is the lowering of the spool top down to the height of the printer case, creating an ideal space-saving fit on my shelf. I narrowed the width of the bracket from 40mm to 30mm and lengthened the rod to accommodate my...

I designed this to be printed on it's side so the layers are perpendicular to the weight of the spool to add strength to the design. On the machine that I designed this for the spool holder has four internal supports... two intersecting supports...It...

The Adventurer 3's filament compartment can only handle small 500g spools of filament designed for it.\r\n\r\nThis low-friction spool holder attaches externally to the filament compartment door, working with my External Filament Mod which runs a...

Heavier spools were making the thread sag, so I reversed the thread so it's more secure (and I added a little "L" on it to remind you its non-standard direction). I also beefed up the contact points to the printer. The final thing was making the lip...

Fortunately, my DIY spool holder worked as intended, although it didn't last long due to an unexpected encounter with my curious dog, who inexplicably enjoys munching on ABS plastic. ... Now that I've donated the printer to a local school, I no longer...

You can easily adjust the mandrel diameter for different spool sizes. I just ran out of red PLA, which would make it look more authentic! UPDATE: I Added the filament guide to the files and to the 123D Design files! Take a look at the new...

updated holder for the v2 based on https://www.thingiverse.com/thing:3808198 made the 4 slots instead of the 3 there removed the lip made it longer to assemble the whole thing (there's 3 other parts, but I didnt edit those) put this in the spool...

I upload spool holders as I purchase them, always keeping them organized and within reach. So far, these models work seamlessly with MatterHackers and Hatchbox 1Kg Filament reels. Hatchbox is 52mm in diameter and measures 63mm from end to end. In...

External Spool Holder for Flashforge Dreamer - Maximizing Your Storage Capacity. ...By its very design, our external spool holder is engineered to accommodate an array of different spool sizes and configurations, giving you maximum flexibility when it...

The FlashForge Guder2 Spool Holder is designed to fit perfectly with 3D fillier spools. ...Included files are the spool holder and retaining nut, providing a secure and seamless printing experience.

Customized version of http://www.thingiverse.com/thing:36112 Spool/Socket Adapter for Filament Storage Solution (http://www.thingiverse.com/thing:743280) Compatible with Flashforge Spools 20mm, Using a 20M Isolation Pipe/Tube as the Base. This...

... needs 100% infill to provide additional support. How I Designed This I designed the spool holder using my expertise in 3D printing technology and my understanding of the requirements for this specific printer model, the FlashForge Creator Pro.

I designed this spool holder specifically for the FlashForge Creator Pro dual extruder printer. After searching Thingiverse for a spool holder supporting SainSmart spools with documentation, I found none that guaranteed my first test print wouldn't...

Spool holder adaptor for Ender 2 Pro. ...Mount the original spool holder on top of the printer.

Adaptor-Ring for my Filament Spool shelf Hanger ( https://www.thingiverse.com/thing:4701052 )

Heavy Duty Spool Mount for 1kg x 1.75mm spools. ... Hub adaptors are any that suit the 3/4" FlashForge Inventor factory shaft.