flashforge spool adaptor 3d models

Simple accessory allows external PLA filaments to feed through the side. Functionality improves significantly when the drum is positioned very close to the printer and spins smoothly without any wobble. The drum shown in the image has an additional...

Something I came up with to run external rolls of filament on my 3D Printer. Two parts: 1) A clip for the back, clips onto the original filament holder, which guides the filament through. 2) An adapter for the head that holds onto the original...

To assemble the adaptor, push the shank through the centre of the old Ormerod filament spool. Next, slide the collet over the protruding end of the spool. Finally, secure everything in place with the clip. ... Printer Settings Printer Brand: RepRap ...

A precision-engineered top load ball bearing spool holder for the guider 2.\r\nI've thoroughly tested this and it functions flawlessly!\r\n\r\nTo accommodate larger printers, I've included a sturdy upright.\r\nAdditionally, a 2-part keyed design is...

This is a filament spool adaptor for an Ender 3V2. ...Made to decrease the ID of the spool on the stock mount so the extruder motor has less resistance and vibrations.

... but I Took the Measurements and Redid the Design in Fusion 360 to Suit Hatchbox Spools. The ID of This Adaptor is 55mm, Which Fits Perfectly Around a Hatchbox Filament Spool, and It Has a 16mm Center Hole That Aligns with the Anyubic Rod.

The adaptor holds the side of the spool securely, and it is durable because it uses bolts, rather than a press-fit or clips that could snap off. The main circular section of this adaptor is 84mm diameter. Most of my eSun spools are 84mm diameter or...

Removing spools is as easy as pressing the release buttons on the sides of the adaptor as you slide the spool off.Note: The hole through the centre is the same size as the rear shoulder on the original spindle. ...Simply remove the spindle, install the...

Adaptor for filament spools to fit snugly onto the rod of a Spool holder (such as Anycubic I3 Mega) enhances rotation ease significantly. This makes handling much easier during printing sessions. Works perfectly with popular filaments like Janbex,...

... spools hang in place. ...As they are non-standard, I've had to design and print adaptors that enable them to spin freely around the 25mm rod or hanger. ...This one is specifically for my current filament spool, the Kexcelled PLA9 Silk from 3DPrintz.

... Recently designed a spacer to enable this modified holder to be used with spools that have a recessed central hub, such as Flashforge spools, and shared my creation on Thingiverse for others to use: https://www.thingiverse.com/thing:3331563

This adaptor fits the Geeetech branded spool perfectly on a 32mm PVC tube used by Geeetech A10, A10M models and similar printers like Ender 3. It makes the spool roll smoothly on the stock holder. I added some lines to this design for easier sanding...

A spool adaptor with bearing for smooth, low force filament feed to the extruder is designed for optimal performance. Modeled in Fusion360 two years ago, it draws inspiration from conical bearings found on Thingiverse. In response to a request on the...

Remix of peaberry's spool adaptor. The sole hard drive I had on hand was the inner part of a bearing enclosed in an aluminum housing. So, I modified this design to accept a 608 bearing instead. It's a tight squeeze, but with just a little sanding,...

This project is best suited for use with peaberry's spool mount, available at https://www.thingiverse.com/thing:2054533. To add a secure grip to the plate, I've incorporated a cylinder that fits snugly inside a 608 bearing. This was a rapid and...

I didn't like the weight of the spool on top of my printer any more So I designed an adaptor to use the original spool holder that came with my MK3, which adapts it to mount on the side of the printer. An easy print part, I printed mine at 0.2 and...

I designed this quick print so you can use cheaper serger cones of thread on your standard home sewing machine.  I designed this for these AK Trading Spools and I'm not sure how standardized these cones are. Please comment if you have success with...

Big spool adaptor for Brother SE-400 sewing/embroidery machine. Should fit the NV180 models too. I made this so I could mount 5000m embroidery thread spools, which are far more cost efficient than smaller spools. Pictured is a Marathon brand...

Notes: This design features a hollow spool with internal reinforcement and an external "hex key" to maximize available space. Prints well on PLA. For best results, a small amount of support is recommended for the spool lock at the top. Works...

100mm hollow filament spool holder with hex key and 75mm long ø50mm adapter. Optimised for PLA. Works well with OmniStand (see below). Print Settings Printer Brand: FlashForge Printer: Creator Pro Rafts: No Supports: Doesn't Matter Resolution:...

This is for the ender 3 pro spool holder - https://www.thingiverse.com/thing:3209211

I have moved my spool to the side of my printer and noticed that the spool keeps turning on an angle while it feeds into the extruder. So I made this adapter which allows the spool to sit on its natural angle. It also means the spool can sit closer...

I modified my own filament spool holder to include four cutouts so it can hold both large filament spools with bores of 50mm plus and smaller spools featuring a small central bore attached to a larger internal bore by four ribs. ... To accommodate...

Here is a rewritten version of the text: A compact spool holder adapter designed specifically for acrylic enclosure modifications, featuring sturdy triangular supports to securely hold heavy-duty filament spools in place.

Place a 120 film spool onto the adapter, then slide it securely into the 116 film camera's loading slot.

BQ Pla 1.75 Filament Spool Adapter, Converts Hephestos Original to Fit 53/25mm Rolls, Easy Installation

I've relocated my spool to a spot beside my printer and noticed that the spool keeps turning at an angle while feeding into the extruder. So, I designed this adapter which enables the spool to sit on its natural incline. It also means the spool can...

I acquired a roll of bright yellow PLA filament, boasting an inner diameter of precisely 57mm, thus I crafted a versatile adapter for this top-notch spool cradle.

Howdy y'all, I've cooked up a handy little script to whip up custom adapters for that fantastic spool holder of yours. You'll find that useful diameters fall within the range of 20mm to 60mm. ...Spooling horizontally just got a whole lot better, friend!

Flat Feet Adapter for Anet A8/A6 Spool Holder, Pre-Configured for M6 Hex Bolts. Attaches the Anet Mounted Spool Holder Directly to a Flat Surface. Perfect for Lack Enclosures. ...Needed: 2x M6 Nut and Bolt per Foot Access to Bottom of Mounting Table