flsun cube instructions 3d models

Remixed fan shroud designed specifically for FLSun kossel delta printers. A direct substitute, requiring no modifications whatsoever. This remixed design combines features from two separate sources: * Dual-directional airflow * An extended tab that...

... work? Post a make! Print Settings Printer: FLSUN SuperRacer Rafts: No Supports: Yes Resolution: .3 mm Infill: 30% Filament: TecBears PETG Black Notes: For best results use PETG, ABS or other heat-tolerant filament. Category: 3D Printer Parts

# **FLSUN Q5 3.5" Display** ## A bigger display for the FLSUN Q5 ### Summary Four brackets at the corners of the control box's display opening are screwed to the existing thread holes. The bracket's arms lead through the opening, holding a Makerbase...

... This triangular support can be found at this link:https://www.printables.com/it/model/381635-flsun-v400-speeder-pad-display I used PLA plus, I think it's the minimum.I used Orcaslicer, with these options: 3 wall, 25% infill (gyroid), (no support)N.

what was NON-working: Delta's Kossel mini from the shop "FLSUN" Self-leveling_effect_set_1 =File Finished Built From Scratch to Work;-) Self-leveling_effect_set_2 = this file Workable;-) Self-leveling_effect_set_3 = File Finished Built From Scratch...

Die originale glatte Umlenkung hat eine Bohrung von 6mm inklusive einer von FLSun hergestellte Buche. Wenn jemand diese weiterverwenden möchte muss diese Konstruktion minimal angepasst werden. Diese Konstruktion hier hat folgende Neuteile notwendig: ...

This is a total overhaul of the Y-Axis for the FLSUN Prusa Printer. It eliminates all acrylic components in the Y-Axis and significantly boosts structural integrity. The design also adjusts the belt orientation. The redesign consists of: Rod...

A hinge for the ORIGINAL FLsun v400 housing(--> English description below the german text)DEUTSCHDrehscharniere für das Gehäuse von FLsun - v400 Drucker. Damit wird die Fronttür des Original FLSun Gehäuses nicht mehr nach oben geschoben, sondern kann...

So, when I installed the magnetic plate on my FLSun SR, directly and not on the glass plate (I removed it), I designed this very, very, very technical piece : a wedge. :) First I only designed the one that was 3mm over the base. So I only have to...

The FLSun is surprisingly a good printer after fine-tuning, but its X-rods aren't aligned, so there's no standard mount available for any accessories. I initially created a quick-release mount, but this one is simpler and requires only two screw...

LED mount for FLSUN SuperRacer to mount a 8 or 10 mm wide LED strip behind the hot end. Slots are included for wire tying the strip, since adhesives aren't great in warm places. Be careful what LED strips you buy. You want one that is 55 mm or...

This is a mount for a FLSun Super Racer Raspberry Pi Camera IR lens. Specifically, this one:...

Things you need for the Power_Off: ---------------------------------------------- 1,20 m cable 2wired Power switch 4x twin plug FLSUN_QQS(PRO)_Power_Off stl FILE Links to my used Products: --------------------------------------...

I loved MatGyver85's optical limit switches, but had trouble getting one of mine to trigger, so I remixed his flags to be one mm taller, so will trigger one mm sooner and you'll lose 1mm of print height. These endstops worked great, but I had to add...

Here is a quick conversion for the FlSun Q5 to MGN12H rails. I used 400mm from my previous printer, 350mm should also work. The BOM needs only 12 M3 T-Nuts and 18 M3x8mm Screws (some washers recommended). The original belt fits tightly (5 teeth per...

I printed with 'armadillo' nylon alternative filament and it seems very strong. You will need the front piece of the clamp from here: https://www.thingiverse.com/thing:2143520 Photo shows my remixed clamp for 4020 fan from here...

Designed specifically for FLSun SuperRacer. The originals were made out of PLA and weren't sized properly so most of them broke. The way the fittings on the SR are sized makes them not very compatible with your standard rounded bowden fitting...

A small magnetic wire coupling made for the flsun delta levelling probe. allows quick attachment of the levelling probe, also allows the disconnected probe to the metal case of the printer. Thers also a clip that attaches to the cable to store the...

This is a custom delta effector designed specifically for the FLSun Kossel and an E3D V6 hotend. It utilizes a 40X10mm fan at the front - obtained from Digikey (https://www.digikey.com/product-detail/en/cui-inc/CFM-4010V-185-314/102-4362-ND/7620536)...

Hi FLsun QQ-s-Pro Friends, I always print on glass with a spree on it, this works very well for me. But every time I put the rotten metal clamps on it, I got a little bit away from behind the PC and made a Glass Clamp that can easily be taken off...

Die originale glatte Umlenkung hat eine Bohrung von 6mm inklusive einer von FLSun hergestellte Buche. Wenn jemand diese weiterverwenden möchte muss diese Konstruktion minimal angepasst werden. Diese Konstruktion hier hat folgende Neuteile notwendig:...

https://www.printables.com/model/311405-flsun-v400-enclosure-wip FILTER BOX AND COOLING The filter box is composed by a body, a caps and a active carbon paper retainer (every thing is splitted by 2 in order to print (you can use mirror function if...

Die originale glatte Umlenkung hat eine Bohrung von 6mm inklusive einer von FLSun hergestellte Buche. Wenn jemand diese weiterverwenden möchte muss diese Konstruktion minimal angepasst werden. Diese Konstruktion hier hat folgende Neuteile notwendig:...

Bearing spool holder for the FLSun V400, though I imagine it will probably work with other printers as well. This sits on top of the regular spool holder, and provides a bearing interface, and GREATLY reduces force required to rotate the spool! ...

This is the first prototype of a filament runout sensor mount for the FLSUN Q5. It mounts directly to the right of the extruder and keeps a clean path for the filament using the stock filament holder. It aligns with the holes in the Q5 case, and...

A cube, enclosed within another cube.

English: After setting up the FLSun SR and putting it into operation, I noticed that the filament spool is placed in an unfavorable way and makes the printer very restless. Also, changing the filament was a challenge with the height of the printer...

This is my version of a light weight, extremely functional effector for the FLSUN QQ series of printers. it is designed specifically for dual 5015 blowers and groove mount hot ends like the V6 style hotends, other may fit but not confirmed. This...

This is an improved version of the extruder for flsun i3 plus. Suitable for other 3D printers! Extremely suitable for printing all kinds of materials and most of all suitable and works very well with TPU !!! The frame - the body of the extruder is...

This is a project of ESP32-CAM case for Flsun Q5 3d printer. Parts required for assembly: - 2x M4x8mm screw (could be 10mm too) - 3x M3 nylon nut - 1x M3 nylon spacer 6mm - ESP32-CAM ...