flsun cube instructions 3d models
289124 3d models found related to flsun cube instructions.
cults3d
Y-axis belt tensioner, as a replacement / enhancement for one of the Y-axis shafts. requires: 2x 2GT H-Wheel 20 Teeth for 6mm Belt Bearing 5mm Bore 2x M3 screw 30mm can also be a little shorter 2x M3 nuts 2x M5 hexagon screw 2x M5 nut (lock nut...
thingiverse
I remixed it to utilize standard M4 nuts and screws I already had on hand. ...This bracket delivers a stiffer setup and simply has a more appealing appearance compared to what I'm currently employing.
thingiverse
I created custom cable management solutions for the 20x20 profile, incorporating 10cm strips to ensure a seamless fit. ...After redesigning and thoroughly testing them, I achieved a precise match that meets all requirements.
myminifactory
Y-axis belt tensioner, as a replacement/enhancement for one of the Y-axis shafts. Requirements include: 2x 2GT H-Wheel 20 Teeth for 6mm Belt Bearing 5mm Bore 2x M3 screws, each measuring 30mm and can be slightly shorter 2x M3 nuts 2x M5 hexagon...
thingiverse
The Mono Stabilization System requires a precisely crafted top component to securely hold the 608 ZZ Bearing in place.
thingiverse
<body>This part was designed to replace the original hotend fan support, allowing to place the <a href="https://www.ebay.co.uk/itm/Fan-Turbine-5015-12v-Fan-50-x-50-x15-for-printer-3D-cooler-50mm-15mm-/332427605094">fan turbine 5015</a>, for layer...
thingiverse
This is the latest iteration of my modification, carefully crafted to ensure seamless automatic filament loading with minimal complications. To achieve this design, it's essential to procure a new small bearing 625. ... Original design:...
thingiverse
Y-axis belt tensioner, as a replacement/enhancement for one of the Y-axis shafts. Requires: 2x 2GT H-Wheel 20 Teeth for 6mm Belt Bearing 5mm Bore 2x M3 screw 30mm can also be a little shorter 2x M3 nuts 2x M5 hexagon screw 2x M5 nut (lock nut...
thingiverse
I'm supposed to create these with the nut positioned at the base, but unfortunately, I haven't managed to print them yet. ...I'd highly suggest incorporating a strong adhesive to keep the M3 nut securely fastened in place.
thingiverse
I reinforced my existing brackets by adding additional material to provide extra stability and durability throughout. ...It should now hold up well under stress.
thingiverse
I Constructed This Replacement Because Mine Failed to Function Properly.
thingiverse
Custom Fittings for T-Slot Extrusion Mounts on 2020 Aluminum Systems
thingiverse
I wanted a small hotend because the original one was too long. That's why vibrations get transferred, resulting in a bad print quality. I measured it so that others can use this for other hotends, like the e3d v6 too. ... Have fun
thingiverse
This part was designed using SolidWorks to replace the acrylic OEM Z micro switch arm with ease.\r\n\r\nThe main difference between this and the original is the use of M4 screws that securely attach it to the frame, unlike the single screw on the...
thingiverse
I prefer mounting the sensor directly underneath the plate, which provides ample space for installing a part cooling fan.
thingiverse
This is a revised version for use with 40x10mm fans, specifically addressing an issue where custom support was omitted from one side, allowing the design to be printed directly without requiring additional support within the slicer.
cults3d
In my case its a better solution to mount the Sensor under the plate, so i have more place for a part cooling fan
thingiverse
I designed this upright to be mounted directly on top of the Nema 17 motor for optimal stability. To ensure a secure fit, consider using a washer as added support when screwing down the mount. Be prepared to make some minor adjustments since the...
thingiverse
This is a sub-carriage that rides on X-Rods below the regular carriage that holds the hot end. The main advantage of using this part is that the carriage can be easily swapped out without disturbing the bearings or X-Rods. To assemble this part,...
thingiverse
I designed a miniaturized version of the SKR v1.3 box, which I completed yesterday. The real magic happens when it's placed on top of the box. You can easily fit two standard MOSFET boards onto its surface. Additionally, there is a lid that securely...
thingiverse
I'm eager to share the results with you despite not having printed them out myself. Others have requested a test, and I'm happy to oblige. ...Please feel free to suggest improvements or modifications that could enhance its quality - your input is...
thingiverse
I've created a hollow version of the bearing holder, designed to be reinforced with epoxy to prevent it from breaking. ...I plan to make two STL designs: one for use with liquid base epoxy and another that can accommodate regular resin.
thingiverse
Update 01/20/2020 - I haven't had this printer since mid-2018, I no longer develop it or have any ability to help with issues. FUTURE MODEL TO COME WITH HALF CIRCLE FAN DIRECTORS INSTEAD OF LINEAR FAN DIRECTORS. DISCLOSURE: The original design idea...
thingiverse
I have carefully crafted this LCD TFT32 Case to function seamlessly without relying on the stock M4 Nut, opting instead for a sleek 20x20 aluminum profile. To secure the electronic board in place, you will require four M3 x 6mm nuts and four...
thingiverse
I was messing around with my Y-axis endstop during homing, but things took a turn for the worse when it suddenly slipped out of place. ...In a split second, I rushed to tighten it, only to have the entire acrylic bracket disintegrate into a million...
thingiverse
I built a bracket specifically designed to secure corks to the underside of my bed, and it accelerates the heating process by approximately 25%.
pinshape
Y-axis belt tensioner, designed to replace or enhance one of the Y-axis shafts. requires: 2x 2GT H-Wheel 20 Teeth for 6mm Belt Bearing 5mm Bore 2x M3 screw 30mm, slightly shorter screws can also be used 2x M3 nut 2x M5 hexagon screw 2x M5 nut (lock...