food dehydrator for filament 3d models

This vent and stand is to allow you to place a 20L bucket on your food dehydrator to turn it into a filament dehydrator. ...The stand puts the filament at a good height and you can stack filaments.

This is an extension for the Hamilton Beach 32100C food dehydrator tall enough to fit a spool of 3D printing filament on its side. There is at least one other attempt at an extension for this food dehydrator out there, but this one prints without...

Customize a food dehydrator to steam your 3D printer filament spools

(see video about the issue with PrusaSlicer) This is a horizontal spool roller that fits in a food dehydrator. simply cut one tray to the right size and attach it with ziptie's add some bearing with a inner diameter of 10mm (6900zz) and you'r...

Simple ring extension for a food dehydrator which makes it usable as a filament dryer. Suitable for a 32 cm diameter dehydrator. A 90 mm wide spool fits inside the dryer with one ring extension. The rings can be stacked up to get a higher...

3-4-19 There is now a single piece version for 330mm/13"+ print beds: https://www.thingiverse.com/thing:3468826 3-4-19 Glue up version prototype: https://www.thingiverse.com/thing:3470025 Original: This is a riser for the common...

3-4-19 There is now a single piece version for 330mm/13"+ print beds: https://www.thingiverse.com/thing:3468826 3-4-19 Glue up version prototype: https://www.thingiverse.com/thing:3470025 Original: This is a riser for the common...

for SANLUX HPS-28FD 使用這個外殼，可不需破壞乾果機托盤以適合線軸，有2種高度2cm及10cm可選擇，可和原廠托盤堆疊。整組由六片組合而成，依上面標示數字連接，組裝最後一片需將模型些微扭曲方可套入。 補充：如果使用PLA材料列印，使用時機器設定溫度不要超過60度，否則底部左側會變形。

As filament rolls does not fit inside most cylindrical food dehydrators, I added a simple wall construction - you need two prints for one filament roll to fit. Several such walls can either be piggy-backed or set up with a dehydration grid in...

Print out 4 of these to make an insert that can be put into a food dehydrator for drying your filament. The parts all bolt together with M3 hardware. Print out of PETG or something else with higher temperature usage. Make sure the diameter fits your...

When trying to search for things it does not return any results.** Original creator: jbanion Link: https://www.thingiverse.com/thing:2669646 This is simply a single pin for jbanion's filament dryer mod. ...I needed another pin but didn't want to print...

... a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. ... It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the back-center. ... A M3-.50 nut is required.

Print these with 0.8-1.2mm walls & 5-10% infill from PETG or other heat resistant filament, Glue together and re-use the lid that came with the food dehydrator. ... Credit to Damien Samson for the idea of using the food dehydrator, Design by Aedan @...

For suntec food dehydrator Prints without support! (PETG) just add some bearings (6900ZZ) with 10mm inner diameter. (Note, this one has some problems with the air thats comming out of the dryer! ...there is an updated one, u can find in remixes.)

This is a snap-together shroud/spacer to allow for filament drying in the OSTBA 240W Digital Food Dehydrator: https://www.amazon.com/gp/product/B085QKT3V4/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 There are several other good designs out...

This is a snap-together shroud/spacer to allow for filament drying in the OSTBA 240W Digital Food Dehydrator: https://www.amazon.com/gp/product/B085QKT3V4/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 There are several other good designs out there...

Use your Presto food dehydrator as a filament dryer, without any destructive changes that would interfere with using it for its original designed purpose. Concept inspired by [thing #4856292](https://www.thingiverse.com/thing:4856292), but...

This will allow you to keep the dehydrator intact for food drying and also use it to dry filament and desiccant bags. You can print 1 ring and the lid to dry a single large filament roll or some desiccant. Or print 2 or 3 rings and and dry more...

Addition for standard food dehydrator. Diameter of dryer tray is 320 mm (Emax) or 270 mm. There are two versions lower is 40 mm high and higher 80 mm high (+100mm). Print 3x or 4x as one part covers 120 or 90 degrees. (These can be customized in...

There are several Spool adapters for food dehydrators out there to save your food trays for drying desiccant packets or even food. The only ones that I could find that were single prints (for large printers), all needed supports. So I designed a...

Food Dehydrator Filament Mount Secure a long PTFE tube to the tip of the mount arm using a zip tie or tie wire.

My idea is to continuously dry heat the filament while printing using a modified food dehydrator. This is a good method because some of my structural projects required 12hrs+ printing and I don't want to expose or wet my filament from moisture...

I bought this food dehydrator on Amazon to dry out filament: https://www.amazon.com/dp/B018UR4XJI?psc=1&ref=ppx_yo2_dt_b_product_details However, there was not enough vertical space to house my old filament spools. Therefore, I made some extenders...

I use a regular food dehydrator for drying filament as the PrintDry does. As i own a big enough printer, lets print it! I use a 1.0mm Nozzle, but its not dialed in correctly. So i dont have a good printed version of this by now. First Prototype...

This is based on the multitude of DIY videos and articles about adapting a food dehydrator for 3D filament use. This extension collar is designed for the [Rosewill Countertop...

This is a remix of Debren27's Filament Spinner for dehydrator (https://www.thingiverse.com/thing:3661551). Reason for this remix is first of all my dehydrator has slightly different dimensions. Second the original design only sits on top of the...

I'm using https://www.printables.com/model/58726-filament-dryer-extension-for-esperanza-dehydrator for my dehydrator. This means the spool is balancing directly on top of the source of hot air. I wanted to raise it a bit to improve air circulation,...

this part allows you to use Geepas Food Dehydrator to dry your Filament without breaking the Trays ( Geepas trays are 32 cm diameter it may fit other Food Dehydrator brand - or + 0.3 cm ) it can fit 2 of esun spools with closed Top or 3 spools with 7...

Food Dehydrator: Knowing of the many projects online where food dehydrators are changed into filament dryers, I bought myself a very cheap one at a thrift store. It is a ROTATING food dehydrator, one where the whole stack of trays turn, while the...