fpv250 3d models
50 3d models found related to fpv250.thingiverse
Replacement leg for Diatone FPV250 frame. Works with 'pointy leg' version (see photo). ...May work for other frames with tilted motor base.
thingiverse
Bridge to mount apm on HK FPV250. ... Use small washers and servo screws to mount.
thingiverse
Top plate for HobbyKings Spec FPV250 quadcopter. Opening to allow access to buttons for kk board. ...Adds real estate to allow fitment of extra hardware...
thingiverse
HobbyKing Spec FPV250 V2 Quad Copterhttp://www.hobbyking.com/hobbyking/store/__52863__HobbyKing_Spec_FPV250_V2_Quad_Copter_ARF_Combo_Kit_Mini_Sized_FPV_Multi_Rotor_ARF_.html This is a simple holder for 3mm led:s mounted in the arms. ...It´s done in two...
thingiverse
It's been designed to fit the FPV250 Mini quad frame 250mm. I made 4 socket for screws, but since the Makerbot cannot print hi-res screws (like the M2.5) I left the holes very small so you can use a M2 or a self drilling screw. ... PRINTING...
thingiverse
FPV250 frame can be obtained from here:ARF, with motors, ESCs, batteryBare frame only Cameras taken into account:420TVL 700TVL Sony with OSD control connector (in metal housing) History: 2014-05-21 Made small holes larger, increased clearance for...
youmagine
Alternative version of the mount for other quads / planes are included.Alternative camera backplates are included for mounting the camera lower / from the bottom (as on planes)Needs a small servo for tilt.FPV250 frame can be obtained from here:...
thingiverse
The motor mount is quite a structural weak point on the Diatone FPV250 frame. If you have broken the arm or the motor mount, you can print this support plate to fix it. You will need 4 M3x20mm screws to attach the plate to the frame and 4 M3x10mm...
thingiverse
this is a replacement for the FPV250 quad cage , it works great and it is strong , I build this one for a friend that has this quad and broke the carbon fiver cage ,he want it the middle to by solid for hes Velcro so there is 2 files to download , I...
thingiverse
Mount and case for the HK FPV250 frame with a house for the 1/3-inch SONY CCD Camera cut down to 32x32mm Instructions One of my 1/3-inch SONY CCD cameras broke after a minor crash so I made this mount and cover to protect it better and be able to...
thingiverse
This is a tray that you can bolt to the underside of the FPV250 found at hobbyking. In my case this allowed me to mount a 4xESC to the bottom of the airframe, and then mount the battery to the tray. The feet line up with holes in the frame. I used...
thingiverse
If the land gear of your Hobbyking FPV250 dropped in a field like me... ...this is a spare part for it...http://hobbyking.com/hobbyking/store/__56663__HobbyKing_FPV250_Racer_Long_Frame_Upgrade_kit.html
thingiverse
This is a plate that can be used with the Diatone FPV250 frame to hold a mobius or other camera. ...Mounted to frame with dampening balls, camera held down by velcro strap Using these dampening balls from Hobby...
thingiverse
Landing Gear for FPV250 sold by Hobbyking or Banggood I designed these Landing Gear because I always lost or broke the original feet. Tested the design yesterday and it is very sturdy. Total height is 54mm so there should be enough space for 4s...
thingiverse
... who needs a longer landing gear quickly. I think a better solution would be to remove the legs altogether and have a helicopter skid, that way the battery could also be mounted underneath allowing more clearance for 6 inch props on the FPV250.
thingiverse
The Hobbyking FPV250 plastic frame isn't the greatest for mounting the flight controller on and maintaining clean wiring. This bracket mounts with the normal hole spacing, allows for the flight controller (NanoWii in my case) to mount to the top, and...
thingiverse
Mount on FPV250 quad for Naza Instructions I made with support, 0,2 layer thickness and 5% infill.
thingiverse
A 20° mount for an Eachine EF-01 on a Hobbyking FPV250 frame, for fun times. ...Post-Printing Mount with 2 cable ties
thingiverse
hk fpv250 / fpv260 up-swept landing gear I have used this on my hobbyking fpv260 up-swept, but it sould fit on comparable models. Printing with PETG gives the most robust restult. There are some tie-wrap holes so if the do come off, you don't have to...
thingiverse
Simple boards to attach different Flight controllers to basically any frame with hole spacing to fit a KK2 board. Instructions I use zip-ties to attach the FC to the conversion board and the supplied...
thingiverse
Landing gear for the Hobby King FPV 250 quadcopter frame.
thingiverse
Camera mount for the Hobby King FPV 250 quadcopter frame.
thingiverse
parts for Hobbyking FPV 250 quadcopter frame. upper plate allows you to see the screen on a KK2 board, LED strip holder fits front and back of the upper plate. ...Strong and light prop guards and landing gear which can both be secured with a single...
thingiverse
This is my first attempt to make landing gear for the Diatone/Hobbyking/ 250 frame. I have designed these as part of a project to create an X8.There are 2 sets of legs depending on where you plan to mount them. These legs allow 6 inch props to be...
thingiverse
Modified version of jkoljo's part. ... I moved the tabs around, and made it just right for a Diatone FPV250 quad frame
thingiverse
FatShark 900TVL camera holder for HobbyKing FPV250 Racer Long Frame Upgrade kit. ... Print Settings Printer Brand: RepRap Printer: ...
thingiverse
Motor mounts with bolt hole pattern for the Daitone FPV250 airframe. Angles the motors down 10 degrees for less drag when racing. Instructions .15mm layers, 15% infill. Thick pieces fit between the...