fractal meshify c vertical gpu mount 3d models

 <img src="img/probe_cutout.png">    - (printability) cutout for heatbreak setscrew is now a a straight-sided slot not a matching hole    - (printability) heatsink to toohead back mounting screws are no longer through...

2.Print the Base Panel & Extrusion Mount with at least 3 perimeters and 30% Infill. Personally I used 4 perimeters and 30% infill to maximise rigidity and reduce any potential flexing. 3.As per previous designs there are some sacrificial layers to...

The chuck holder is assembled to the "chuck mount pad" with the "holder" and "holder keeper". This is the upper portion. Depending on manufacturing tolerances of the chuck, bolt, and bushing, you may want to pick up some small thin washers to put in...

When mounting the laser in the LASERBEAM tunnel, the housing will block excess light, resulting in sharp, straight outline lines and a clean green square screen. Making your own slides is easy and fast, thanks to 3D printing. You can design new...

using 70% ethyl alcohol. Printed cute octopus using Polysmooth Natural (from Polymaker sampler pack) Close-up of the polished cute octopus Change Log 2017-04-03: Added piezo buzzer mount to power panel Uploaded Fritzing diagram 2017-04-04 Uploaded...

I have been switching out handlebars/brake levers with this particular bike, & I really don't want to unwrap the bars just to swap out for longer housing. Note: this only works for the Tektro fork crown-mounted cable hanger...

... This stops the button from getting hung up inside the case during assembly. **Update 01/18/20:** I added a 6mm hole to the base near the relay connectors, allowing users to run hidden wires behind the drywall to a wall-mounted garage door button.

The node is mounted in the node-box via clamp strips. This solution offers the advantage that the node can be easily removed from the box. In addition, there is sufficient space for cable connections from both sides of the board. The node-box...

On top, the nuts are recessed, on bottom the rods stick out (you need some play for mounting) and you can put the little covers (screw_cover.stl) on top of that for better looks and protection from scratching. Due to popular demand (the people being...

The mask has been designed for you to be able to take the Dome on and off, which locks in place with a solid 6 pin system, so it won't rattle around and mounts snug onto the face mask. The facemask has small cut outs on the side and under the mouth...

The reason I remixed the design is because I needed a bit more space to accommodate my effector with 5015 fans mounted to it. So I added about 23mm of extra clearance to the sides. In my case I didn't need to change the door, however I am remixing...

The biggest compaint I have seen about them is that they are not securely mounted to the Pi. They only attach via the GPIO pins, there's no provision for a standoff or a screw. So I've made a STABILIZER part that will brace the Mini Fan, to prevent...

You have to keep the wires between the plates fairly short so that they will fit in the fan mount. I recommend you cut, strip, and tin the short (~25mm) wires first, then add them incrementally until you have all six plates joined so that the...

### NEW: ### **[Universal Buttonbox](https://www.thingiverse.com/thing:4567163) (for example for enclosures)** ## UPDATES: ## 19/06/2020: The 4_E3-BB_10Buttons_Mount.stl was modified to remove overlapping geometry as it caused slicing problems in S3D...

mounting. There's no compartment for the battery yet, but that might be an additional part that screws onto the body afterwards. There will be a top plate screwed on which still needs to be designed. I'm going to print the body as is out as soon as...

What's IncludedThe entire Anvil Digital Forge Patreon release for May 2021, including; CharactersThe Gauss Sniper, Wall Runner & Crouching Pilot 1 x Female Recon Trooper Sniper body with hex-camo cloak (the head, optical link cable, and hood are...

A fully detailed interior and pilot can be included.Mech Rifle Assembler that allows you to mix and match any gun barrel, ammo feed, magazine, and sight with any other to create over 1500 combinations! You can completely customise your mech's gun as...

I chose to mount the door on the table tops themselves (see pics), but this comes with the side effect that you'll need to cut away a bit of the veneer on the table to let the door sit flush. I did end up really liking this approach so it's how I'd...

An almost free of play support for the Bowden tube in direct interaction with the presented powerful pneumatic couplings, shorter retractions are possible, and a sudden loss of tension is less likely to occur.• Integrated cable Management.• There...

Mounting on the wrist is done with Velcro. I used both 38mm and 50mm (1.5" and 2") Velcro. There's a printable piece for the leather bracer pattern that you need to flip over to draw the full size cuff. I used one-way stretch imitation leather. My...

I sugest that you sort the cards lexically though.The item cards are used a bit more often, but that is before you star a scenario, so that can with ease be taken out of the box when needed and put back again.It is seperated into, mounts, weapons,...

I have not drilled holes because with a simple drill they are easy to make and adapt to any mounting on different skates. It would be easy to include them, maybe I'll get around to it. I have also included a design with logo. Finally I have...

This poking allows easier mounting of the propeller, it was a scary amount of pressure before doing that. Your printer may be different of course. - Two of the same (at least) are always needed - to be specific, if one of these printed ones is...

I used a B10 base candelabra style LED at 40 watts with a Christmas village light bulb base (the clip fits right in the column to secure it with no glue) - There is an adapter for a tea light included that slides into the column if you want to go...

If you want to recreate this you'll need the following things: -transparent filament for Playstation logo -black (or colour you want) filament for the lamp case -on/off snap in switch...

A single piece of wire (I used motorcycle safety wire) is bent (see pictures for shape) to form the loops for tie on and the hook mounts and fits in between the halves before gluing together. I printed this one with a .25 nozzle and .10 layer height...

To be specific, I used the end stops(?) for the twist motion as mounting points(?) so that it doesn't twist, so yes, this mod will render the twisting motion completely null, but there is actually a reason for this. The Joystick has a POV switch(4...

base pieces, arm pieces, and cover pieces).\nThe best method involves simultaneously printing both left and right component pairings at once so as to improve detail on finer features\nTo add density and further aid in support creation while also...

BTW, If you need digital calipers or rubber bands I have provided a few links here (As an Amazon Associate, I earn from qualifying purchases.):Digital Calipers: https://amzn.to/48G64VRRubber Bands: https://amzn.to/46AjFMuStep 10If your probe is...

It would be nice if you added photos of the body printed and mounted on the chassis. My body is printed from PETG. I tried to make the parts printable without supports. I made assembly instructions. To connect the cabin, I recommend gluing nuts or...