frosthaven vs gloomhaven 3d models

Flat-top treasure chests for gloomhaven or frosthaven, Flat top allows characters mini's to stand on top Two seperate files: BOX and FRAME Print both and snap the box into the frame. YOU MAY WANT TO SCALE UP THE FRAME to 101 or 102% to make it...

This is just another version of a hit point tracker for Gloomhaven. Magnets can be added to make them stackable, and I use the same magnets that i use with the MagHex system I found here at Thingiverse. There is a +10 hit point marker to put in the...

In our Gloomhaven group, we're always teasing each other when someone decides to loot some coins. We hate Ooze. The #1 looter Ooze trophy was born. I made this to pass on after every game session to the number 1 looter of the evening. Photo of...

Ability card holder for the board games Gloomhaven and Frosthaven. ... - Keeps your ability cards organized - Side slot stores your hand of cards between turns - Saves table space (Place it in the 'discard' or 'lost' position and leave the other one...

This is an adaptation of the Crystal Cluster scaled for Gloomhaven / Frosthaven with included hex tile.

Adds a slight bump to the inside of the slots because some Frosthaven cardboard monster standees would slip out too easily. Prints in place just fine on my Bambu P1P at 0.2mm with no supports, no raft, and no brim. I use a sharpie to color the...

... better than a dashboard due to its modular nature. And I can reuse for frosthaven later. Remix was done in tinkercad. ... Credits: https://www.thingiverse.com/thing:4555403 Linked is the good design, use mine if you are cheap and impatient.

A d20 based monster organiser/tracker for Frosthaven and Gloomhaven Inspired by https://www.thingiverse.com/thing:4200007 Recreated in FreeCAD to create a modular design that allows swapping of parts and doesn't require the whole item to print in a...

Gloomhaven / Frosthaven dashboard with HP and XP trackers and item slots (that can also hold active cards). The depth of all slots works with sleeved cards. This is the optimal layout for my purposes. I made the text embossed so that it can be...

A Quick Modification to the "Gloomhaven Boss Standee Base" to add on a holder for status conditions and character tokens.

I was looking for some entry and exit tiles to print for our Gloomhaven sessions but couldn't find any.Therefore, I created them according to the designs in Jaws of the Lion, Gloomhaven, and Frosthaven rule books.These tiles fit the MagHex tile...

This is a poop hat to show enemies that are marked by Call of the Abyss, an ability of the Deathwalker class. Backstory: I started referring to the shadows appearing on the ground as "pooping" out a shadow. Which quickly progressed to calling the...

WARNING! This print has a low tolerance for inaccuracies, recommended layer height 0.12 (not 0.2 which is standard). This is a brutal press-fit (use clamps that can apply pressure centrally). Once its in the standee it needs about 3 full rotations to...

While being delighted by standee holders like https://www.thingiverse.com/thing:2810528 me and my group always found the condition markers clumsy to attach and remove to the base, especially when the room is crowded. So I designed this clip where the...

Made a nice and matching Barrels version for frosthaven as a way of thanks for all the free stuff I donwnloaded from here, there is probably some more to come

This is primarily a remix of ChrisTheViolaNerd's and MechEngineerMike's light up crystals, formed onto a 3 hex base for use in Frosthaven. ... I tried to make it hollow so that an LED light could be used underneath but had no luck, feel free to remix...

Here's my take on the Frosthaven monster, the Abael! As you can see, this guy needs a bit of support to print, mainly on the left hand and around the bands that hold his armor on. Because he's hunkered down like that, the model is relatively short...

Here's my take on the Frosthaven monster, the Abael! As you can see, this guy needs a bit of support to print, mainly on the left hand and around the bands that hold his armor on. Because he's hunkered down like that, the model is relatively short...

Just touched up the front plate in tinkercad to say Frosthaven instead of Gloomhaven. ... No other changes

This is a condition clip for Frosthaven monsters. ... It might be a bit tight on Gloomhaven monsters since they use a slightly thicker card stock.

I took a similar design from gloomhaven and designed it specifically for the frosthaven monsters. It worked out well with the lid having the names of each monster recessed. v2: of Lids with lettering extruded on the inside of the lids for easier...

Remix for Frosthaven Character Icons

Quick "White Card" item from Frosthaven; applies -1 to a normal/elite monster's attacks. Used Pirata One, the Gloomhaven font. ...I wanted to test Organic Supports, so I printed it like this, but you might want to lay it on its side and print w/o...

Fortunately, Frosthaven comes with a plastic organizer tray for all of the overlay tiles and bits and pieces, however there is still no organizer for map tiles or monsters standees. FYI I'm considering making an e-bay auction for quality resin...

This is a simple remix of the brilliant canopy tree by Robagon for Gloomhaven, looking more like a frozen tree for Frosthaven. All praise should go to Robagon and Curufin for their great models. https://www.thingiverse.com/thing:2807576 ...

Unfortunately Frosthaven has more monsters than Gloomhaven and the standees are bigger, so it has to be two boxes. I suggest using a filament switch to make the embossed numbers white. Use the Document as a reference for which standees are in...

This page contains the character-specific files meant to be used with the base box here.For each box you will need to print 3 models:one of the characterbox_(size).stl models from this page for the box.The (class)_characterbox_lid.stl file for the...

This adds Frosthaven support to two of my favorite Gloomhaven Things: * [Gloomhaven Character Box](https://www.thingiverse.com/thing:2994130) by jgrg1, or [my remix of the same](https://www.thingiverse.com/thing:4808239) * [MagBox Dashboard and...

I needed something to hold all the standees that Frosthaven gives you. ...Holds 36 Standees, I think Frosthaven comes with like 33-34 Feel Free to Remix.

This could be used fairly well for the OG Gloomhaven monster, the Living Spirit, or even for any sort of wandering spirit in a DnD game =) The chains needed a ridiculous amount of support to print successfully, so I went ahead and included a version...