fs ia6b 3d models

Antenna mount for FS-IA6B receiver

receiver FS IA6B for RC equipmentFlysky FS-i6X

i designed this fs ia6b receiver holder mounted on my f450 drone

Mount for the FlySky FS-IA6B

Flysky FS-iA6B 2.4G 6CH Receiver PPM Output is a great reciever, I bought this second hand, the previous owner said he lost the case, so I made one. Feel free to remix! ... -Plug and Play (No adhesive) -No support -under 4 Grams

2.4GHz ,6 CHANNEL RECEIVER

Caixa para reduzir o tamanho do FS-IA6B Ideal para quem usa iBus, basta remover os Pins e soldar diretamente na PCB.

This is a simple holder for a FS-iA6B Radio Receiver. The holder is 49 mm wide, 12 mm in height and 10 mm deep. ... The mounting holes are 39 mm apart and uses M3 or #4 screws.

This is a simple holder for a FS-iA6B Radio Receiver. The holder is 49 mm wide, 12 mm in height and 10 mm deep. ...The mounting holes are 39 mm apart and uses M3 or #4 screws.</p>

# FS-IA6B quadcopter receiver mount The FS-IA6B mount dedicated to the 210mm frame. In my case is the Lisam LS-210. I decided to create the mount for the top of the frame because I have no space between levels. It's more dangerous instead of on...

This is to hold a FS-iA6b Receiver on a Tarot 680pro hexacopter. I designed it to be mounted along with a HERE 3 GPS stand (see pictures) The Here 3 GPS stand can be found here. ...https://www.thingiverse.com/thing:4864451

This is a antenna mount for the FS-iA6B. This is specificaclly designed for the Eachine Wizard, but may fit other frames e.g. Martian 2 Antennae are at 45° to each other. I think optimum is 90°(?) but I've had no issues with this. The pitch of...

This is a Single Antena mount for Flysky FS-ia6B or Fs-ia style recever Print it in PLA or TPU For PLA put 103 or 105 flow

Mingalaba, this is the mount for the FS-iA6B reciever on QAV-R. You need 3mm carbon tube or Plastic tube to cover the antenna and it is 90 degree V shape between 2 antenna for the best signal of transmitting and receiving. ...Print Settings Printer: ...

Twin antenna holder for FlySky FS-iA6B. Used on Eachine Racer 250. ...Print Settings Printer: Creality CR7 Rafts: ...

Eachine Racer 250 FlySky FS-IA6B receiver mounting bracket. This is designed to get the receiver up over the top of the flight controller and allow the VTX cables to pass underneath. I am using this with a rear mounted VTX to move everything inside...

This is a carrier for the FlySky FS-ia6b receiver. It is designed for a sailboat, but may work for other projects as well. It is designed to position the antenna in the most favorable way (at 90º to each other and at the top of the hatch) and...

For the FlySky IA6b receiver on my FT Spear, I wanted to have an antenna mount. I designed this mount, so the two antenna's are 30 degrees apart from each other to enhance reception. Installation is very simple and the mount suits a broad...

antenna stand

flysky fs-ia6b - dual Antena Mount - Martian 215

Modified version of my Flysky FS-IA6B receiver mount to get the receiver and the VTX even lower. Flysky FS-IA6B receiver mount for the Martian II quad frame. Mounts in the back of the quad between the 4 rear standoffs and is secured with a zip-tie.

Flysky FS-IA6B receiver mount for the Martian II quad frame. Mounts in the back of the quad between the 4 rear standoffs and is secured with a zip-tie. I also added 30x30 standoffs for adding other equipment, in my case I am using the Eachine VTX-03...

I updated my FS-IA6B mount to hold a microphone, the microphone that I am using is the Adafruit Electret microphone amplifier - MAX9814 with auto gain control. I also changed the VTX from a VTX03 to a ATX03, the dimensions are the same but the ATX03...

Put in place the support, add first receiver and in second place the antennas for lock all. ... Suggesion are welcome ;)

I've printed this support for holding my antennas in the right way, then i fixed the support to the plane with the biadhesive

Designed with angle between antennas 90 degree as in manual. This mount will fit for all antennas in diameter 5mm. ...For mount you need only 1 hole.

This object was made in Tinkercad. ...https://www.tinkercad.com/things/jWiTTQn2iuR

Printed with PLA Pro, 205C, 3 shells to make the thing durable and rigid enough. OpenSCAD source attached. Use 6mm heatshrink tubes or drinking straws (better option - they're more rigid) to cover the antennas. Depending on how accurate your...

Edit it online https://www.tinkercad.com/things/6AtagVnSzoY Lien vers le [Flysky FS-iA6B 2.4G](https://www.banggood.com/Flysky-2_4G-6CH-FS-iA6B-Receiver-PPM-Output-With-iBus-Port-p-978603.html?p=ZA15057386539201611F)...

Back mount for a Martian II frame to put in the FPV and the antennas of a FlySky FS-IA6B (or similar) receiver. ...They do an angle for better reception and if builded with flexible filament can absorb crashes.