ftc robotics 3d models

Here is a battery holder for FTC robots. It has plenty of mounting holes (Tetrix spacing, 16mm between holes) as well as its own slide-off cover. There is enough clearance for full-size screws (you don't need low-profile screw heads) and the battery...

this is a foam based launch motors for the 2016-2017 FTC robotics Competitions V2 is the better one Print Settings Printer Brand: LulzBot Printer: TAZ 5 Supports: Doesn't Matter Resolution: 100% Infill: 50% Notes: im guessing this may need supports...

The original Onshape file is linked, you will need to change the ‘TeamNumber’ configuration value to your team number.Use color change g-code to make it easily readable. The mounting holes should line up with REV robotics 8mm hole spacing.

Designed to work with REV robotics components.Core Hex Motor3x8mm hex bolts3x16mm hex bolts3mm Nylok nuts15mm extrusionGT2 6mm belt (commonly used in 3d printing)6mm idlersZip tiesYou can use a simple extension spring inline with the belt to keep...

FTC robot for the 2017-2018 game. ...As you can see this model was created before the game reveal so some parts can make no sense.

Any questions not answered or further explanation is needed please contact with the subject FTC Robot If you need building instructions or a complete parts and file list, please contact with the subject Information FTC Robot If you need further...

- Any questions not answered or further explanation is needed please contact with the subject FTC Robot - If you need building instructions or a complete parts and file list, please contact with the subject Information FTC Robot - If you need...

Turpin FTC Robotics Designs 2017-2018

We have created this bracket for us with the Tetrix kit of metal parts designed for use in FTC Robotics competition. We designed this because we wanted a cheaper alternative to the metal ones that are commercially available. These cost between ten...

It's designed to bolt into the hole spacing for Tetrix which is used in FTC robotics competitions. You'll need tiny screws to hold the sensor to the holder as shown in the photo. ... It's probably best to use brass so the magnetic sensor doesn't have...

These are the 3D printed parts we used to build our linear slide for our FTC robot in the RESQ season. There is one linear bearing that goes between two pieces of MiSUMi extruded aluminum, and one linear bearing that goes on the side of the linear...

<p>Use color change g-code to make it easily readable. ...The mounting holes should line up with REV robotics 8mm hole spacing.&nbsp;

<p>Use color change g-code to make it easily readable. ...The mounting holes should line up with REV robotics 8mm hole spacing.

Customized version of https://www.thingiverse.com/thing:3045130 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3045130

2016-2017 FTC Competition Robot

This is a phone holder designed by Attack On Robot FTC Team #10664. It works with the MotoG phone. ... Email attackonrobot10664@gmail.com with any questions or suggestions.

This is a robotics team, Business Card. It Folds out into a rocket. ... It will fly a lot further with 1-2 Rubber Bands!

Any questions not answered please email me at theev123@gmail.com with the subject Complete FTC Robot Se this robot in action the bottom left robot (the colorful one)https://www.youtube.com/watch?v=rDLTHs4qklc To modify the files go to onshape.com...

Any questions not answered please email me at theev123@gmail.com with the subject Complete FTC Robot Se this robot in action the bottom left robot (the colorful one) https://www.youtube.com/watch?v=rDLTHs4qklc To modify the files go to onshape.com...

This is a simple FTC robot I designed for rover ruckus, it is designed to use aluminum extrusion and 3d printed parts.Update after competition: This robot was the only one scoring in the top of the lander averaging about 3-4 minerals per game. Sadly...

Any questions not answered or further explanation is needed  please contact with the subject Complete FTC Robot   See this robot in action by searching "FTC Team 247 Reboot finals" on YouTube   Just a quick summary, this project is a full size,...

I remixed a design by MrPTrog to hold my FTC Robotics (11341) phone to our robot using a Tetrix mount. You can test to see if this will fit your phone in its cas without printing the whole thing by printing the Moto_X_clip_Fit_Test_1.stl file first....

FTC Robotics Odometry Pod designed by team 9849. Open source, feel free to modify and make your own. Ensure that you take the mirror of the sides when you 3D print them. They or not the same, but rather mirror images. This is due to the countersunk...

Print Settings Rafts: Doesn't Matter Supports: Doesn't Matter

<p>Will fit 5 mm hex shaft and 9mm 2GT belt.<br><a href="https://brazosportisd.onshape.com/documents/8520f4ed4222eafabb847345/w/6cdf5063348e2874b9b690c3/e/f4731cc7a6a5a1dc207e19a3?aa=true">Onshape file</a> -&nbsp;<br>Use configurations to change the...

2015-FTC-robotic-lifting-mechanism

Rev Robotics Battery Holder

This is a pulley cover we have designed to attach to the REV Robotics channel. ...Attached are the files to print just one, or sixteen covers.

This is a low cost measuring cube for FIRST Tech Challenge, brought to you by Team 19589, Falcons Robotics from Ridgeline High School in Liberty Lake, WA. Materials needed: - 3D Printer and about half a spool of filament. Print: - (4)...

This assembly is 12961's full drivetrain which was designed to be modular from season to season. The main plates are meant to be cut from 1/4 inch aluminum, but with thicker pocketing it could go down to 1/8 inch aluminum. They are meant to go...