functional print 3d models

Add a rubber band to the side pins and a small 3mm magnet at the barrel's base. ...Alternatively, print it in one piece for a decorative display.

Boost speed settings to override coasting mode and optimize flow. ...Elevate print rate to approximately 40 millimeters per second. ...Set layer thickness to 0.2 millimeters.

This is a print in place fully 3D printed launcher. It can launch a BB bullet over 10 feet. It can launch anything that fits in the .5 inch diameter barrel. ...Just put something in the barrel pull back the plunger on the bottom and let go.

Here is a Christmas Tree that looks somewhat closer to the real thing, and that you can actually hang ornaments from.This model was designed with PrusaSlicer in mind, so match any slicer terms to your slicer's equivalent.Each piece should be printed...

... on to dry and have soapy water drain out. ...Fits default size of a bar of soap, but feel free to adjust the scale to fit any type. I printed this in black NinjaFlex for less slipping on smooth surfaces. ... Print as is in the file with no supports.

Every print can be printed on a single extruder without any supports needed, and the tallest print is 155mm high on the Z axis. So as long as your printer can print up to 155 in the Z direction, you can make this project no problem. The only thing...

The handle only requires two main prints, and you have the option of printing six individual sliding cylinders or one with all of them already embedded. Every print can be made on a single extruder, no supports are required, and the tallest print...

Printed in PLA at a 0.2 layer height, the top took approximately 19 hours and weighed about 450 grams. Each leg pole required around 8 hours to print, weighing roughly 150 grams each. The foot for one table part took only two hours, weighing...

I printed the right side then the left and sanded the two side that were going to be glued together, just so the glue would bond better. I used J-B Weld Plastic Bonder. each side took about 21 hours with the concentric 3D infill. I hope it prints out...

... part of this incredible community. Your support means the world to me. **Print Settings** **Printer Brand:** Ultimaker **Printer:** Ultimaker 3 **Rafts:** Yes **Supports:** Yes **Infill:** 23% **Notes:** Printed in Black ABS - A true delight!

This is a small water pump working with a 9v dc motor. ...You also need 2 m3 screws with nuts. Everything is printed in PLA with 0.12 layer height.

It's essential to note that this hookah must be printed using ABS material due to its glass temperature properties. PLA is not suitable because it has a Tg range of 50-60°C, which can cause the part holding the rosh to reach high temperatures. When...

i wanted switch and i could not afford to wait for delivery and there was nothing like this on internet so i designed it its easy to setup and you shouldnt need to do much of post procesing print with 100% infill support: off nozzle 60 bed 230...

... If you want to purchase these files already printed in peak quality, I highly recommend checking out DRUCKADO. ... Product Overview Guillotine (5 parts) Guillotine supported (5 parts) Product Information  Around 80 mm from feet to eyes LINKS

A working push pin, kind of. ...A blower fan is highly recommended to avoid a print that looks like mine. Follow me on Instagram at https://www.instagram.com/brian3dprints. Buy the filament used in this 3D print from Amazon:

Print Settings: Printer: Delta Kitset Rafts: No Supports: No Resolution: 0.3 Infill: 20% Notes: The small spring pieces may present difficulties attaching them to your print bed; in this case, rafts or glue stick can be used to aid the bonding...

I broke the racket near the handle the first time when I printed it with 0.2mm layer height, 15% infill, and 3 walls - Although this was PLA.Print the racket in two sections with their connected sides facing the bed, and set up automatic tree...

The handle only requires two main prints, and you have the option of printing six individual sliding cylinders or one with all of them embedded in it. Every print can be done on a single extruder without any supports needed, and the tallest print is...

You may be able to print it as is, but best to check if you need to change one of these measurements.Printed with PLA, not the best when it comes to heat, but holds up just fine as it doesn't get much abuse when its warm. ...Best to print with PETG if...

printed in PLA at 0.2 layer heights&nbsp;top took 19 hours to print approx. 450 grams.</p><p>leg poll for 1 took 8 hours approx. 150 grams.</p><p>foot for 1 took 2 hours approx. 50 grams.</p><p>leg hub took 6 hours approx. 150 grams.</p><p>only the...

For resin and FDM If you would like to get early releases with lower prices, or want to sell your prints of this model, please subscribe to my Patreon at Patreon.com/MyPokePrints for exclusive models, discounted pre-releases, and a growing community...

... and can accommodate a 5mm LED for illuminated buttons. There are two styles: a standard-looking version and a "miniskirt" option for easier printing and reduced plastic usage. ...I'm currently redesigning this as a customizable OpenSCAD object.

This model originated from Fable and underwent thorough preparation for print production, featuring smoothing techniques to ensure a smooth finish. Upon conversion into a box format, it measures precisely 10cm in length, allowing users to...

A 3d printed suppressor designed for the threads of 14ccw. I put this on my krytac airsoft gun. The internal baffles might need to be filed/sanded to fit. I used sound isolating foam in between each baffle. ...Super glue worked great to hold it...

This 3D printable pencil prints in two parts without supports. Video here: https://www.youtube.com/watch?v=bhWODQaPgQU Infill: 100% Layer height: 0.12 mm Bed adhesion recommended This takes 0.7 - 1.00 mm pencil lead (depending on...

... from the iconic navigation buoys used by the US Coast Guard on both coasts. ...Their unique internal design allows them to be printed without supports, while still maintaining enough hollow space to provide sufficient buoyancy for a contact key.

Upon downloading you agree to use the files for personal purposes only.This means you do NOT have the right to sell 3D prints of the digital files, including selling the products from moulds. If you would like to legally sell 3D prints of my models,...

... much everywhere. It can open in 180°. No pin required! Properties of the non-scaled model: • Has an 5 mm thick printed pin, giving the hinge high strength. • The holes are sized for M3 screws. • The smaller contact surface is 20 mm wide. ...

... poly gun. ...DOESN'T WORK (please don't ban me thingiverse). Not much to recommend for printing other than to try to minimize supports. ...Dimensions are likely very small, so you can scale it up and down to what ever you want in your slicing software.

A printed seal made of PETG. Can be used to hold objects with a little effort or for decoration. Jaw mounted on a ball joint to be nested during assembly. Lever in two parts with the cap to be glued. ... https://www.youtube.com/watch?v=VagFXiR_fus