funktion 1 speakers 3d models
898620 3d models found related to funktion 1 speakers.cults3d
L= 29.9mm Depth = 15.95mm Height = 1.9mm *Measured on printed part, resin. For personal use, not for resale. Not for redesign. Contact me if you have issues or need it modified, and I will see what I can do. ... Information and measurement might be...
prusaprinters
Schlüsselanhänger-Dübel d6-D8 L39 Schlüsselanhänger mit Funktion Dekorativer Schlüsselanhänger und wenn einem mal beim Renovieren Dübel fehlen lassen sich bis zu 3 Stück hier ausbrechen und in ein 8 mm Bohrloch (min. 42 mm tief gebohrt) einsetzen um...
cgtrader
Classic computer speakers 3D Models, nr. 1 in my collection. 2 individual objects, sharing the same non overlapping UV Layout map, Material and PBR Textures set. Production-ready 3D Model, with PBR materials, textures, non overlapping UV Layout map...
grabcad
Technichal:Frequency Range (+/-3 dB) [Hz]: 51 - 26,000Sensitivity (2,83 V/1 m) [dB]: 86Nominal Impedance [ohms]: 6Maximum SPL [dB]: 106Recommended Amplifier Power [W]: 25 - 100Crossover Frequency [Hz]: 2,800Crossover Principle: 2-wayHigh frequency...
3docean
Speakers audio tower system 2.0 Speaker diameter HF-1 , wideband speakers-4, LF-8 ‘ Frequency range 20-20000 Hz Signal-to-noise ratio 70 dB Crosstalk 45 dB 4 ohm impedance 220 V power supply Office Sidebar Size 32×82×18 cm
3docean
Game-ready, PBR, UV-unwrapped, Textured Speakers 3D Model, with PBR materials, textures, and non overlapping UV Layout map provided in the package. Made in Blender 3D (Cycles materials) and in 3D Studio MAX 2012 (V-Ray Adv 2.30.02), then...
thingiverse
This is a NON FUNKTION Glock 17 sliced to fit in a 12mmx12mm Printer with connector pins. ... I attatched the whole Model for People with big enough Printers.
grabcad
Specifications Frequency Range (+/-3 dB): 53 - 26,500Hz Sensitivity (2,83 V/1 m): 86.5dB Nominal Impedance: 6Ω Maximum SPL: 106dB Recommended Amplifier Power: 25 - 100W Crossover Frequency: 2,900 Hz High Frequency Driver: 1 x 25 mm Soft Textile Dome...
thingiverse
Print 3 with the round hole for the left, and back-left and back-right speakers Print 1 of the big mount for the center speaker. subwoofer goes on the floor usually, I didn't make a mount for that one, if you want one, make a comment, I can...
thingiverse
This remix includes all files needed to print a 2.1 setup with AMP, Speakers, and Subwoofer. I designed these files specifically to fit the 4-inch Aiyima Speakers and 5.25-inch Aiyima Woofers in the Sub The design is also updated to accept standard...
prusaprinters
This is a remix of guppyk2 speakers.This remix includes all files needed to print a 2.1 setup with AMP, Speakers, and Subwoofer.I designed these files specifically to fit the 4-inch Aiyima Speakers and 5.25-inch Aiyima Woofers in the SubThe design is...
thingiverse
Sealed Subwoofer: f3 = 70Hz (2.921 Liters) PR Subwoofer: f3 = 50Hz + 4dB @ 75Hz (25g Mass on PR, 5.979 Liters) Subwoofer Parts: Tang Band W5-1138SMF 5-1/4" Paper Cone Subwoofer Speaker - Part # 264-917 Dayton Audio DS215-PR 8" Designer Series...