futaba r7008sb receiver 3d models

Futaba R7008SB receiver Holder

Futaba R7008SB receiver Holder Print Settings Printer Brand: Creality Printer: CR-10 Rafts: Doesn't Matter Supports: No Resolution: 0.2 Infill: 35% Filament: Tesla Filament PLA RED Category: 3D Printing

This RC receiver mount guarantees a 90° spread of your antennas, and it looks very neat inside your model. Print out of PETG to prevent warping in sunny days. ...Add silicone sleeve to the antenna for a tight fit in the print.

Futaba R7008SB RC receiver

I wanted a Box to mount and protect the F7008SB futaba reveiver on my Backpack L and Trike L I mounted this on the back of the Backpack L under the Motor Controller. I wanted this outside to be able to not have the Lipo banging it. On the trike...

Does require Supports

Does require Supports

Holder for Futaba R7008SB FASSTEST receiver.

Holder for Futaba R7008SB FASSTEST receiver.

This thing is a Receiver Mount, especially for a Futaba R7008SB. ...The holes in the top are for antenna-tubes and the hole in the back is for the ext-voltage cable

This thing is a Receiver Mount, especially for a Futaba R7008SB. ...The holes in the top are for antenna-tubes and the hole in the back is for the ext-voltage cable

Support pour montage dans un modèle réduit avec deux récepteurs FUTABA R7008SB. ...Il est collé au scratch. Protection à l'arrère pour les antennes. Support for double R7008SB FUTABA receiver. ...Mounting with scratch

A model of a Futaba Receiver

Utilisation de tube de coton tige pour protéger et tenir les antennes 14/06/2019 : added a remix version with a small bossing inside to maintain the receiver inside the box easily, look at the inside screenshot / ajout d'un bossage intérieur pour...

Futaba receiver R617FS

Futaba-603FF receiver

Receiver Mount Futaba R304SBE for RC Car

Mounts your R7008SB receivers with approx. ...1mm clearance for the Evojet Power Jack.

I made this tray with antenna tube holders for my RC 3D printed ship as I wanted to keep the receiver high and dry (and so I can remove my expensive Futaba R7008SB receiver from a potential sinking scenario). The tray comes with a zip-tie channel so...

Mount for Futaba R2008SB receiver on a ImmersionRc Vortex 285. ...

A printable Mount for the Futaba R6203SB Receiver

Solid Model of the Futaba R6208 SB receiver with decals.

RC Futaba R2004GF

Futaba 2,4 Ghz Empfänger

This is the R2008SB 2.4GHz S.Bus S-FHSS 8 Channel Receiver for use with the Futaba 8J 2.4GHz Computer Radio System. ...You can find it here : http://www.gpdealera.com/cgi-bin/wgainf100p.pgm?I=FUTL7608

Outer case for the Futaba R2106GF Receiver. ...The case it comes with is a bit flimsy, so this gives it a tough outer shell whilst giving space for the antanna wire, bind button and status LED.

I wanted to create a clean and solid way to mount a PowerBox - Systems Evolution together with a Futaba receiver (RS7008SB) inside a plane. The result is a simple mount that can be used with most Powerbox models and Futaba receivers. Small slots to...

Simple tub style receiver holder.

Futaba rc are expensive, and FASST can be bound to any model repeatedly. The holder will be secured using zipties, and foam beneath. Secure the rx using 20mm 3mm or 1/8 bolt. for inch size you need to probably enlarge the nut hole. You still...

This receiver mount guarantees a 90° spread of your antennas, and it looks very neat inside your model. Print in PETG to prevent warping in sunny days. ...Add silicone sleeve to the antenna for a tight fit in the print.